Еxample:- Let us represent the body's surface tissue as layer of thickness X1=5 cm which has a thermal conductivity K= 0.59 J/m.s. °C . This is surrounded by a layer of tissues fat of thickness X,-2 cm with K,-0.21 J/m.s. °C .The body's interior is at temperature T-37°C and the skin temperature is T,=33.5°C.What is the heat loss per unit area?

Еxample:- Let us represent the body's surface tissue as layer of thickness X1=5 cm which has a thermal conductivity K= 0.59 J/m.s. °C . This is surrounded by a layer of tissues fat of thickness X,-2 cm with K,-0.21 J/m.s. °C .The body's interior is at temperature T-37°C and the skin temperature is T,=33.5°C.What is the heat loss per unit area?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.23P

See similar textbooks

Similar questions

A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
You are designing a small heatsink to cool a high-powered IC on a control unit PCB. The IC puts out 40,000 W/m2 and has a size of 40mm x 20mm. A fan blows 40 degrees C air across the IC at a speed of 4 m/s. The IC is well insulated on its back face. If the convection coefficient is 62 W/m2K, what is the surface temperature of the IC?
A food product with 80% moisture content in a 7 cm diameter can wants to be frozen. product density is 1000 kg / m³ thermal conductivity is 1.0 W / (m K) and initial freezing temperature is -2.25 degrees Celsius after 8 hours in freezing medium -35 degrees Celsius Temperature to -10 degrees Celsius estimate convection heat transfer coefficient freezing medium assume the can as an infinite cylinder h =
Yes it is hard but please I need help with this A horizontal 8 cm OD pipe carries steam at 150°C through a room at 17°C. The pipe is covered by a1.5 cm layer of magnesia insulation. What is the heat loss per meter of the pipe?• For this configuration if a horizontal cylinder, NuD = f (RaD, Pr) can be found using equation 8.28• I assume since material and thickness of the pipe inside the insulation are not given, nor is any flow data onthe steam that these resistances are negligible.• The temperature of the outer insulation is not initially known. I guessed it and used a circuit diagram with tworesistances to find Q, then used one circuit to find the wall temp, and iterated. I updated my material propertieswith my wall temperature changes. It converged quickly.• My answer is 5-10% higher than the books. Not sure why.
A 100 mm diameter steam pipe is covered by two layers of lagging (insulation). The inside layer is 40 mm thick and has a thermal conductivity of 0.07 W/m K. The outside layer is 25 mm thick and has a thermal conductivity of 0.1 W/mK. The pipe carries steam at a temperature of 234°C , where the outside temperature of lagging is 24°C. If the steam pipe is 20 m long, determine (a) The heat lost per hour, (b) The interface temperature of lagging. Neglect the resistance of steam pipe as well as the convection resistances.
A cylindrical shape body of length is 1.9 m and diameter is 400 mm is inside a room where the ambient temperature is equal to 300 K. The initial temperature of the body is equal to 350 K. If the heat convective coefficient is equal to 1.3 W/m^2.K. What is the thermal conductivity K.
A horizontal copper plate 10 cm thick is initially uniform in temperature at 250◦C.The bottom surface of the plate is insulated. The top surface is suddenly exposed toa fluid stream at 80◦C. After 6 min the surface temperature has dropped to 150◦C.Calculate the convection heat-transfer coefficient that causes this drop.
The walls of a refrigerator are typically constructed with two metal panels enclosing an insulation layer. Consider an insulation layer made of fiberglass (k = 0.046 W/m°C) with a thickness of 50 mm, placed between two metal sheets (k = 60 W/m°C), each 3 mm thick. If the wall separates cold air at 4 °C from ambient air at 25 °C, what is the heat received per unit area, considering internal and external convective coefficients equal to 5 W/m²°C?
Find the minimum amount of diameter for the insulation of a spherical water tank? Radius of the tank is 10 m, thermal conductivity is 25 W/(m^2*K) and convective coefficient is 5 W/(m*K)
An insulated steam pipe is routed horizontally through an unheated room, then vertically to the ceiling. The pipe is insulated, and the outside diameter of the insulation is 15 cm. The horizontal and vertical lengths of pipe are both 4 m long. The outside-surface temperature of the insulation is 50°C, and the room temperature is 5°C. How much heat is lost from the insulation by convection?
Fluid flows over a flat plate, 1.2 m long. The direction of flow is along the length of the plate and parallel to the surface of the plate. The plate is held at a constant temperature of 283 K. Velocity and temperature profiles are assumed to be linear inside the boundary layers. The free stream temperature of the fluid is 340 K and it travels at 5 m/s. The fluid properties are as follows: thermal conductivity = 0.029 W/mK, density = 0.92 kg/m3, viscosity = 12.9 x 10-6 Pa.s, and specific heat capacity = 1003 J/kgK. The value of the Nusselt number at the tailing edge of the flat plate is: [ans1] The convective heat transfer from the middle of the flat plate is: [ans2] W/m2 step by step working out piease, hit final answer is 145, -281 respectively