Exercise 1: Humidity detector We propose to study the assembly of figure 1 which allows the ignition of a red diode from a certain percentage of humidity in the air detected by a sensor. The assembly elements are: VDD 3V, R₁=1ks, R₂=10002, R3-27092. Diode D₁: VSD1 1.2V, RSD1=12 22. Transistor T₁: B=100, VCEsat 0.2V and its base VST1=0.6V, RST1=1kQ2. The value of the resistor RH depend on the air humidity's percentage (noted X) following the relation RH=30X; where R₁, is in 2 and X in %. In all numerical applications, we will suppose that B+1 B. VDD is referenced to ground. 1. Determine the expressions of the elements of the equivalent Thevenin generator (indicated on the figure) according to VDD, R₁, R₂ and RH.

Exercise 1: Humidity detector We propose to study the assembly of figure 1 which allows the ignition of a red diode from a certain percentage of humidity in the air detected by a sensor. The assembly elements are: VDD 3V, R₁=1ks, R₂=10002, R3-27092. Diode D₁: VSD1 1.2V, RSD1=12 22. Transistor T₁: B=100, VCEsat 0.2V and its base VST1=0.6V, RST1=1kQ2. The value of the resistor RH depend on the air humidity's percentage (noted X) following the relation RH=30X; where R₁, is in 2 and X in %. In all numerical applications, we will suppose that B+1 B. VDD is referenced to ground. 1. Determine the expressions of the elements of the equivalent Thevenin generator (indicated on the figure) according to VDD, R₁, R₂ and RH.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
How is a solid-state diode tested? Explain.
Apply each of diodeapproximations and determine:a. Current through D1b. Voltage across D2c. Voltage across R3 GIVEN: R1 = 2 kΩ, R2 = 1.2 kΩ, R3 = 6.8 kΩ E= 10 V D1: Si, rB = 2 Ω, rR = 220 kΩ D2: Si, rB = 5 Ω, rR = 560 kΩ DETERMING FIRST IF IT IS A FORWARD BIASED OR REVERSED BIASED THEN, SOLVE IN FIRST APPROXIMATION, SECOND APPROXIMATION AND THIRD APPROXIMATION SHOW THE CIRCUIT DIAGRAM IN EACH APPROXIMATION
A practical silicon-based solar cell is constructed from a n+p junction. a) Explain briefly the meaning of the notation n+? b) Draw a sketch showing the device structure of this solar cell. c) This cell shows a photocurrent IL = 10.9 A under AM1.5G illumination. If the temperature is 25 oC, what is VOC? Assume that the saturated current IS = 1×10−9 A.
In your own words(not googled) please answer and help me understand the following a. What is a LED? Explain the working of a LED and give at least two applications. b. Why do LEDs need series current-limiting resistors? c. How does LED differ from an ordinary diode? d. What is a photodiode? Explain how it works and give at least two applications. e. What is a/an: i. Tunnel diode ii. Optoisolator iii. Varactor diode iv. Shockley diode
Apply each of diode approximations given the following parameters D`:rB= 2 ohms, rR= 220 kilohms: Si, rB = 5 ohms, rR= 560 kilo ohms Determine the current flowing through D1, D2 AND R2, R3, THE VOLTAGE ACROSS R3 SOLVE IN THREE DIODE APRROXIMATIONS
A sample of n-type silicon semiconductor has the following properties:Donor density Ndis 5x1019per cm3Mobility of electron is 1500 Mobility of hole is 500Electron charge q = 1.602x10-19coulombs.Intrinsic carrier density ni= 1.45x1010per cm3a)Find the density of holes and electrons in this sampleb)Find the conductivity of the given sample if the. c)What is the resistivity of the given sample?
1. Given the circuit below. Answer the following: A. Which diodes turned ON? The diodes are made up of Silicon and the diode internal resistance rD is 1 Ω. B. What is the current (in mA) in the circuit? The diodes are made up of Silicon and the diode internal resistance rD is 1 Ω. C. What is the voltage (in V) across the 100 Ω resistor? The diodes are made up of Silicon and the diode internal resistance rD is 1 Ω.
(02) DC Si Diode Circuit. (Course: Electronic Devices and Circuit Theory) What is the minimum value for RL needed to turn Zener diode ON?, And what is the maximum value for RL needed to turn Zener diode is ON? -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
Which of the following ratings (PIV- Peak Inverse Voltage and temperature) is true? A)Si diodes have lower PIV and wider temperature ranges than Ge diodes. B) Si diodes have lower PIV and narrower temperature ranges than Ge diodes. C) Si diodes have higher PIV and narrower temperature ranges than Ge diodes. D) Ge diodes have lower PIV and smaller temperature ranges than Si diodes.
2. A certain zener diode has a maximum power rating of 300 mW at 40 deg Cand a derating factor of 1.4mW/deg C. Determine the maximum power the zener can dissipate at a temperature of 80 deg C. 3. From the datasheet, a 1N4728A zener diode has a ZZ of 10 0. The datasheet gives VZ = 3.3 V at a test current, IZ, of 76 mA. What is the voltage across the zener terminals when the current is 90 mA? When the current is 45 mA?
1 (a) Suppose in a donor doped semiconductor at a particular temperature, EF is 0.015 eV above than ED level when Ec-ED = 0.045 eV. Comment on whether there will be partial ionization or full ionization in this case. 1 (b) When EF touches intrinsic Fermi energy EFi, comment on whether an extrinsic semiconductor will stay extrinsic or not. What will be ultimate state of semiconductor in this case? Don,t copy from anywhere.