Exercise 2 Triangular Cycle. ble consider the reversible cycle below described by an Ideal gas. Xx 1. In which direction must this. the operation to be motor - lone ? cycle 2. Calculate the efficiency to be Constant. assumed Numerical -2 Pot Po A application: B 99 a a function Yz Cp Cv travel for 8 = 1.1 + V Vo 2No Please answer the above question step-wise, showing detailed explanations with diagrams if necessary. Thanks in advanced !!!

Exercise 2 Triangular Cycle. ble consider the reversible cycle below described by an Ideal gas. Xx 1. In which direction must this. the operation to be motor - lone ? cycle 2. Calculate the efficiency to be Constant. assumed Numerical -2 Pot Po A application: B 99 a a function Yz Cp Cv travel for 8 = 1.1 + V Vo 2No Please answer the above question step-wise, showing detailed explanations with diagrams if necessary. Thanks in advanced !!!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
Combined Rankine Cycle Show the details of your solutions with Schematic and TS diagrams Performance between: Condition 1 Required PH = 17 MPa, 10000C Thermal Efficiency ? PR = 8 MPa, 8000C PReg = 4 MPa PL = 0.008 MPa Condition 2 Required PH = 17 MPa, 10000C Thermal Efficiency ? PReg = 8 MPa PR = 4 MPa, 8000C PL = 0.008 MPa
please solve it i need urgent A naturally-aspirated (NA) oil engine (i.e., a slow-speed CI Engine) which produces one power pulse in two revolutions of its crankshaft is to be designed to operate with the following characteristic at sea level where the mean atmospheric conditions are Pa = 101325 N/m2 and ta = 17°C. The value of gas constant of air is Ra = 0.287 kJ/(kg·K). Gross brake power, Wb, gross = 300 kW Volumetric efficiency, hvol = 80% Brake specific fuel consumption, sfcb = 255 g/(kW·h) Actual air-to-fuel ratio, (A/F)act = (m a / m f )act = 17:1 Angular speed of the shaft, w = 125 rad/s Calculate: (i) The required engine capacity Vs, total in cc (cm3), as well as in litres (L); Vs is the swept volume, and (ii) the brake mean effective pressure ( Pbm ). The engine is fitted with a supercharger (SC) so that it may be operated at an al- titude, z, of 3000 m (above sea level) where the atmospheric pressure (Pa) in N/m2 is determined from the following relation: Pa =…
Complete the Carnot cycle performed by air if the parameters in points 1 and 3 are the following: Point 1: P_1=2MPa, T_1=600kPoint 3: P_2=120 KPa, T_2= 300K R=287 J/(Kg K)-air only. Please type answer no write by hend.
An Otto cycle begins its compression at 94kPa, 1230cm^3 and 11degC. The dispalacement volume and maximum temperature within the cycle is 1090cm^3 and 920degC and respectively. Utilizing air standard assumptions, determine the: a. heat addition and Wnet (kJ) b. thermal efficiency (%)c. mean effective pressure (kPa) Consider the cycle as a model of the process in each cylinder of a spark-ignition engine. Show the T-s and P-v diagrams when solving. Note that specific heats are not constant
10. The initial design of an IFR turbine is to be based upon Whitfield’s procedure for optimum efficiency. The turbine is to be supplied with 2.2 kg/s of air, a stagnation pressure of 250 kPa, a stagnation temperature of 800°C, and have an output power of 450 kW. At turbine exit the static pressure is 105 kPA. Assuming for air that γ ¼ 1.33 and R ¼ 287 J/kg K, determine the valueof Whitfield’s power ratio, S, and the total-to-static efficiency of the turbine.
p103#5. a three-process cycle of an ideal gas, for which Cp=1.064 and Cv=0.804 kJ/kgm.K, is initiated by an isentropic compression 1-2 from 103.4kPa, 27degree C to 608.1kPa. aconstant volume process 2-3 and polytropic 3-1 with n=1.2 complete the cycle. circulation is a steady rate of 0.905kgm/s, compute (a) QA, (b) Wnet, (c)e, (d) Pm.
Complete the Carnot cycle performed by air if the parameters in points 1 and 3 are the following: Point 1: P_1=2MPa, T_1=600k Point 3: P_2=120 KPa, T_2= 300K R=287 J/(Kg K)-air only
Provide a long answer using necessary graphs / equations. Describe the Rankine thermodynamic cycle. What thermodynamic processes occurs? Where is the cycle used? How to improve the cycle?
Provide the diagram, given, and step by step solution for below problem. An Otto cycle has an initial condition of 102 kPa and 32°C with compression ratio of 8.The maximum temperature of the cycle is 1400°C. Find the mean effective pressure in Kpa per kilogram of air. ANSWER: 524.66 kpa
Provide complete solution and diagram for below problem. A Brayton cycle has a pressure ratio of 8 and initial temperature of 32oC. Its compressor workis: A. 165.50 KJ/kg B. 182.34 KJ/kg C. 213.45 KJ/kg D. 247.50 KJ/kg Answer: D