A simply supported beam of hollow circular section of external diameter 200mm, and internal diameter 150mm has a span of 6m. It is subjected to concentrated load of 50kN and Udl of 5kN/m over the entire span. Determine the maximum slope at the support and maximum deflection at centre. Take E = 2 x 105N/mm2 (1b)Explain the following terminology: The strain Stress Young modulus in the column. Rigid Prop

A simply supported beam of hollow circular section of external diameter 200mm, and internal diameter 150mm has a span of 6m. It is subjected to concentrated load of 50kN and Udl of 5kN/m over the entire span. Determine the maximum slope at the support and maximum deflection at centre. Take E = 2 x 105N/mm2 (1b)Explain the following terminology: The strain Stress Young modulus in the column. Rigid Prop

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.11.4P: A simple beam AB of length L and height h (see figure) is heated in such a manner that the...

See similar textbooks

Similar questions

A simple beam AB of length L and height h (see figure) is heated in such a manner that the temperature difference 7= T{between the bottom and top of the beam is proportional to the distance from support A: that is, assume the temperature difference varies linearly along the beam: T2- Tt= Tax in which 7"0 is a constant having units of temperature (degrees) per unit distance. Determine the maximum deflection SW9Xof the beam, Repeat for a quadratic temperature variation along the beam, so T2+T1= Tax
A cantilever 8m long carries a uniformly distributed load of 12kN/m from midspan to free end. Determine the deflection at the free end, Find the smallest moment of inertia (in x10^6 mm^4) so that its maximum deflection does not exceed the limit of 1/360 of the span. Use E = 70 GPa. Determine the required depth of beam if it is a rectangular section with width-to-depth ratio of 0.5.
A wooden beam 5 m long, simply supported at its ends and it is carrying a point load of 8 kN at its centre. The cross-section of the beam is 160 mm wide and 270 mm deep. If E for the beam is 70x109 N/m2, the deflection at the centre is
Two elastic beams with equal bending rigidity of EI are connected by a pin at B. The beam is fixed at A and a roller support is attached at C. Beam BC is subjected to a uniformly distributed load of magnitude w=1 N/m. If the bending rigidity EI is 108Nmm2, determine a) the lateral deflection at B, b) the rotational angle at B, c) the rotational angle at C. d) sketch the deformed shape
A cantilever of length 2.5 m carries a uniformly distributed load of 16.4 kN per metre length over the entire length. If the moment of intertia of the beam = 7.95 x107 mm4 and value of E = 2 x 105 N/mm2 , Estimate the deflection at the free end.
An axial member consisting of two polymer bars is supported at C. Bar (1) has a cross sectional area of 2720 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 21,560 mm and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C.
Plot the deflection of a beam with a length of 3 m, the modulus of elasticity of E = 200 GPa, and I = 1.2 ✕ 106 mm4 for a sign weighing 1,500 N. Slope at x=L
Determine the maximum deflection of a simply supported beam carrying a hydraulic cylinder in a machine used to press bushings into a casting as shown in the figure. The force exerted during the pressing operation in 45 kN. The beam is rectangular, 35 mm thick and 150 mm high, and made of steel (E = 207 Gpa).
Please help me for the correct solution. A leaf spring carries a central load of 3000 N. The leaf spring has to be made of 10 steel plates 5cm wide and 6mm thick. If the bending stress is limited to 150 N/mm² determine: (i) Length of the spring and (ii) Deflection at the centre of the spring. Take E = 2 * 10 ^ 5 * N / m * m ^ 2..?
Determine the deflection at the end of the overhang by applying the second moment area theorem. The modulus of elasticity is 500000MPa and the cross section is given below. See figure 10
A simply supported beam of 6 m length with external diameter 150 mm and thickness15 mm has maximum deflection 4.25 mm at the centre. Calculate the uniformlydistributed load carried over by the beam. Take E=210 kN/mm2
A SSB of 8 m span carries a point load of 10 kN at its centre. It also subjects to a UDL of 1kN/m over its entire span. Find the maximum deflection of the beam. Take E = 200 kN/mm2,I = 200 x 106mm4.