Explain each box. which one is blocked and where is aif flowing

Q: Explain the degrees of freedom for the following picture. Answers can be either typed in the box or…

A: GIVEN:

Q: Exhaust manifold manufactured from white cast iron.

A: True True True

Q: A stone is thrown upwards with initial velocity of (20 m s),

A:

Q: la) If a 35 tonne block is raised to 110m and then falls to ground level (in generating mode) in 3…

A: 1a) Given         Mass, m = 35 ton = 31751 kg       Height, h = 110 m          Time, t = 3 min…

Q: I need a solution within 15 minute

A: Let A1 area of semi circleA2 area of rectangleA3 area of triangley1=15y2=15y3=30+13*20 =30+6.67…

Q: 1. Calculate the lost power

A: Taking equation  d^ 2 u(x) dx^ 2 = r(x),x (1(0)= x in[0, pπ] )=u( π)=0 (1) f(x)=sin(x ) We create…

Q: A small velocity probe is to be inserted through a pipe wall. If we measure from the outside of the…

A:

Q: Write the SI units of work done.

A: Work is defined as the product of the displacement and the component of force along the…

Q: I need , RAy and RBy with complete solution. Thank you for helping.

A:

Q: Resolve and draw the diagram of all internal efforts

A: For the above diagram, We draw a free body diagram,

Q: o create a braking system for a vehicle to stop at 7 feet, 5 feet and 3 feet.

A:

Q: ould you please describe this picture for me i have to present it to audienc

A: strength of material is an important subject , it is an important tool in exploring the limits of…

Q: Assume you are a casting engineer working in a foundry in Nizwa. You have to develop the casting…

A: (i) Sand casting is the casting process in which mould has to be destroyed each time to get the…

Q: The given picture shows the following parts of a compressor. Please state its functions and discuss…

A: Given : To find : functions of parts and working

Q: Find the work done when all the water has been pushed out.

A: Given: A=0.1 m2 T1=300 K V1=0.3 m3 P0=100 kPa vf=0.100 m3/kg TO determine: The workdone

Q: Good afternoon!  May I know where is the part of b) 4 mpa. Thank you!

A:

Q: create 3 simple flow chart on how stainless steel, car tires, and coca cola is manufactured.

A: Flow chart for stainless steel:

Q: Stoker

A:

Q: 13) What does Pascal's theorem (wedge proof) state about the pressure at a single point in a fluid ?…

A: Applications of Pascals Law Hydraulic lift When lifting the high load body like a car by applying…

Q: 6 cm 2 cm 4 cm 6 cm

A: Given

Q: If oil with specific gravity of 0.82 is used to measure the atmospheric pressure, how high would it…

A: Given: Sg = 0.8

Q: WRITE SOLUTION HOW DID YOU GET FBD and FBE THANKS

A: How to get the given FBD

Q: You must follow the general guideline that by drinking eight glasses of water each day to ensure…

A: B. False

Q: Describe the similarities and differences between calculadng an average rate of change and an…

A: The average rate at which one quantity changes in relation to something else changing is…

Q: Explain What comes up to your mind when you hear the word Hand Grenade

A: A grenade is an explosive device that is often thrown by hand, although it can also refer to a…

Q: I have a headache. you go to the doctor. (must , should , have to) إجابتك

A: Answers are given below.

Q: What is going on?

A:

Q: Manufacture and design a U-pipe in an open state with a minimum of 7 different fluids with a datum.

A: A u-tube is a simple instrument to indicate the differential pressure between two points The…

Q: kinetic energy a

A: Ek=0.2521 MeV

Q: ANSWER: Re= FLOW: TYPE OF

A: To find :- Reynold no. And ttpe of flow

Q: I need , RAy and RBy with complete solution write it on a paper. Thank you for helping.

A:

Q: Resolve and draw the diagram of all internal efforts.

A:

Q: Calculate the make up rate of the water by doing a material balance between the water stream and the…

A: For set 1 Mass flow rate of makeup water  = m1 dry air *(ω1 B-ω1 A) = 0.0586*(0.017-0.013) Mass…

Q: With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 5…

A: The free-body diagram of the junction of the boom, given load, and the force exerted by the cable,…

Q: Can you please explain why in step 2 the written formula are not matching

A: Hello student  In step 2 for optimal compressor ratio in each stage, the following formula is used

Q: Calculate what is requested please

A:

Q: need the solution for this problem pls. Thanks a lot.

A:

Q: need the solution in h

A: m1=200kgm2=300kgm3=240kgm4=260kgr1=0.2mr2=0.15mr3=0.25mr4=0.3mθ1=0°θ2=45°θ3=45+75=120°θ4=45+75+135=2…

Q: What is the time in seconds to supply a cubical tank whose side is 0.61m if it is literally full and…

A: Diameter of hole (d2) = 2.54 cm= 2.54 × 10-2 m Cubical tank side (Z1) =0.61 m Discharge of tank (Q)=…

Q: speed.

A: Given; A milling cutter having teeth is rotating at;  N= 135 rpmIf the tooth is, f=0.1 mmDetermine…

Q: raw the block diagram for a garage door and explain each block

A: A curved arm is fitted to a garage door opener to help the door's movement. The motor guides the…

Q: use this logo and explain for saftey

A: Given use this logo and explain for saftey