Explore the effect of insulation thickness on the heat loss q and the temperature of the insulation outer surface T2 for a steam pipe of 0.05-m outside diameter that is insulated with a layer of calcium silicate. The temperature of the steam fixed at 600 K and the outer surface is exposed to an airflow (T=30°C) that maintains a heat transfer coefficient of h = 85 W/m².K, which includes the effects of radiation. where r,= 0.025 m and r2 is a variable (0.025 < r2 < 0.50 m). Compute and plot the heat loss and outer surface temperature Ts,2 as a function of the insulation thickness.

Explore the effect of insulation thickness on the heat loss q and the temperature of the insulation outer surface T2 for a steam pipe of 0.05-m outside diameter that is insulated with a layer of calcium silicate. The temperature of the steam fixed at 600 K and the outer surface is exposed to an airflow (T=30°C) that maintains a heat transfer coefficient of h = 85 W/m².K, which includes the effects of radiation. where r,= 0.025 m and r2 is a variable (0.025 < r2 < 0.50 m). Compute and plot the heat loss and outer surface temperature Ts,2 as a function of the insulation thickness.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.18P

See similar textbooks

Similar questions

3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
2.42 A circumferential fin of rectangular cross section, 3.7-cm OD and 0.3 cm thick, surrounds a 2.5-cm- diameter tube as shown below. The fin is constructed of mild steel. Air blowing over the fin produces a heat transfer coefficient of K. If the temperatures of the base of the fin and the air are and , respectively, calculate the heat transfer rate from the fin.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed eccentrically within a larger cylinder of 85 magnesia wool as shown in the sketch. The outside diameter of the larger cylinder is 15 cm and the surface temperature is 50C.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.
A horizontal, 3-mm-thick flat-copper plate, 1-m long and 0.5-m wide, is exposed in air at 27C to radiation from the sun. If the total rate of solar radiation absorbed is 300 W and the combined radiation and convection heat transfer coefficients on the upper and lower surfaces are 20 and 15W/m2K, respectively, determine the equilibrium temperature of the plate.
Question 1:A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg=1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15oC and -20oC, respectively, ona cold winter day, what is the rate of heat loss throughthe glass? To reduce heat loss through windows, it iscustomary to use a double pane construction in whichadjoining panes are separated by an air space. If thespacing is 10 mm and the glass surfaces in contact withthe air have temperatures of (last two digit of your Registration number) oC and -15oC, what isthe rate of heat loss from a 1 m x 2 m window? Thethermal conductivity of air is ka=0.024 W/m.K.
Question 1: A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 oC and -20 oC, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of 20 oC and -15 oC, what is the rate of heat loss from a 1 m x 2 m window? The thermal conductivity of air is ka = 0.024 W/m.K.
Steam at a temperature of 723 K is flowing through a pipe with an outer diameter of 100 mm. The pipe is insulated with 30-mm thick mineral wool, the average thermal conductivity of which is 0.065 W/m.K. Determine the outside surface temperature of mineral wool if the ambient air temperature is 300 Assume the hot-surface temperature of the mineral wool is the same as that of the flowing steam and the value of the surface coefficient of the insulating material is 33 W/m2.K.