Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN: 9781305387102
Author: Kreith, Frank; Manglik, Raj M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 2, Problem 2.42P
A circumferential fin of rectangular cross section, 3.7-cm OD and 0.3 cm thick, surrounds a 2.5-cm- diameter tube as shown below. The fin is constructed of mild steel. Air blowing over the fin produces a heat transfer coefficient of
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A long stainless-steel (AISI 316) steam pipe, with an inside diameter of 6.00 cm and an outside diameter of 8.00 cm, is covered with a layer of asbestos insulation (k = 0.150 W/m-K) 1.00 cm thick, which in turn is covered with foam insulation (k = 0.044 W/m-K) 6.00 cm thick. The inside surface temperature of the stainless-steel steam pipe is measured to be 250.0°C, while the outside surface of the foam is exposed to convection, T_inf = 25.0°C, h_inf = 15.0 W/m^2-K.
• Draw and label a sketch of this system. Include dimensions, known temperatures, etc.
• Draw and completely label the corresponding 1-D steady-state conduction resistor diagram.
• Determine the heat transfer rate through the pipe per unit length.
• Calculate the temperature at the asbestos/foam interface.
1.
(a)
Consider a room with a 1.8-m-high and 2.0-m-wide double-pane window consisting of two 4-mm-thick layers of glass separated by a 10-mm-wide stagnant air space. The convection heat transfer coefficients on the inner and outer surfaces of the window are 12 W/m2 K and 25 W/m2 K, respectively, while the average thermal conductivity of glass is 0.78 W/m K; and the air, 0.026 W/m K.
If the room is maintained at 22 oC, the outside temperature is -4 oC and heat transfer due to radiation can be neglected, determine:
(i)
Draw the sketch and thermal resistance network;
(ii)
the total thermal resistance;
(iii)
the steady rate of heat transfer through this double-pane window;
(iv)
the temperature of the inner surface of the window.…
/ Hot square plate (1 m ×1 m) is to be cooled by attaching aluminum circular pin fins (D=0.25 cm, L= 3 cm) distributed with distance 0.6 cm as illustrated in Figs.(1-a) & (1-b). If the fin base temperature is 100°C, cooling air temperature is 30°C and h= 35 W/m. °C. Determine the total rate of heat transfer from the finned plate and the effectiveness of the fins? Assume k= 237 W/m.°C and nr=tanh mL/ mL.
Chapter 2 Solutions
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
Ch. 2 - A plane wall, 7.5 cm thick, generates heat...Ch. 2 -
2.2 A small dam, which is idealized by a large...Ch. 2 - 2.3 The shield of a nuclear reactor is idealized...Ch. 2 - A plane wall 15 cm thick has a thermal...Ch. 2 - 2.5 Derive an expression for the temperature...Ch. 2 - A plane wall of thickness 2L has internal heat...Ch. 2 - 2.7 A very thin silicon chip is bonded to a 6-mm...Ch. 2 - 2.9 In a large chemical factory, hot gases at 2273...Ch. 2 - 2.14 Calculate the rate of heat loss per foot and...Ch. 2 - 2.15 Suppose that a pipe carrying a hot fluid with...
Ch. 2 - Prob. 2.16PCh. 2 - Estimate the rate of heat loss per unit length...Ch. 2 - The rate of heat flow per unit length q/L through...Ch. 2 - A 2.5-cm-OD, 2-cm-ID copper pipe carries liquid...Ch. 2 - A cylindrical liquid oxygen (LOX) tank has a...Ch. 2 - Show that the rate of heat conduction per unit...Ch. 2 - Derive an expression for the temperature...Ch. 2 - Heat is generated uniformly in the fuel rod of a...Ch. 2 - 2.29 In a cylindrical fuel rod of a nuclear...Ch. 2 - 2.30 An electrical heater capable of generating...Ch. 2 - A hollow sphere with inner and outer radii of R1...Ch. 2 - 2.34 Show that the temperature distribution in a...Ch. 2 -
2.38 The addition of aluminum fins has been...Ch. 2 - The tip of a soldering iron consists of a 0.6-cm-...Ch. 2 - One end of a 0.3-m-long steel rod is connected to...Ch. 2 - Both ends of a 0.6-cm copper U-shaped rod are...Ch. 2 - 2.42 A circumferential fin of rectangular cross...Ch. 2 - 2.43 A turbine blade 6.3 cm long, with...Ch. 2 - 2.44 To determine the thermal conductivity of a...Ch. 2 - 2.45 Heat is transferred from water to air through...Ch. 2 - 2.46 The wall of a liquid-to-gas heat exchanger...Ch. 2 - Prob. 2.47PCh. 2 - The handle of a ladle used for pouring molten lead...Ch. 2 - 2.50 Compare the rate of heat flow from the bottom...Ch. 2 - 2.51 Determine by means of a flux plot the...Ch. 2 - Prob. 2.52PCh. 2 - Determine the rate of heat transfer per meter...Ch. 2 - Prob. 2.54PCh. 2 - 2.55 A long, 1-cm-diameter electric copper cable...Ch. 2 - Prob. 2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Circular fins of uniform cross section, with diameter of 10 mm and length of 50 mm, are attached to a wall with surface temperature of 350°C. The fins are made of material with thermal conductivity of 240 W/m·K, and they are exposed to an ambient air condition of 25°C and the convection heat transfer coefficient is 250 W/m2·K. Determine the heat transfer rate and plot the temperature variation of a single fin for the following boundary conditions: (a) Infinitely long fin (b) Adiabatic fin tip (c) Fin with tip temperature of 250°C (d) Convection from the fin tiparrow_forwardA horizontal pipe having a surface temperature of 67 °C and diameter of 25 cm is buried at a depth of 1.2 m in the earth at a location where k = 1.8 W/m-°C. The earth surface temperature is 15 °C. Calculate the shape factor if the pipe length is 10 m.arrow_forwardA spherical object with a temperature of 700 oC, made of carbon steel with a diameter of 3 cm, will be cooled to 370 oC by an air flow with a temperature of 35 oC and a heat convection coefficient of 90 W/m2K. Calculate the time (s) required to cool the body, ignoring the temperature gradient inside the body and making any other assumptions you deem necessary. The heat transmission coefficient of carbon steel can be 45 W/mK, its density is 7800 kg/m3 and its specific heat is 480 J/kgK.arrow_forward
- A 4-m-high and 6-m-wide wall consists of a long18-cm * 30-cm cross section of horizontal bricks (k =0.72 W/m·K) separated by 3-cm-thick plaster layers (k =0.22 W/m·K). There are also 2-cm-thick plaster layers on eachside of the wall, and a 2-cm-thick rigid foam (k = 0.026 W/m·K)on the inner side of the wall. The indoor and the outdoor temperaturesare 22°C and 24°C, and the convection heat transfercoefficients on the inner and the outer sides are h1 = 10 W/m2·Kand h2 = 20 W/m2·K, respectively. Assuming one-dimensionalheat transfer and disregarding radiation, determine the rate ofheat transfer through the wall.arrow_forwardCalculate the quantity of heat conducted per minute through a duralumin circular disc 119mm diameter and 22.65mm thick when the temperature drop across the thickness of the plate is 9.3°F take the coefficient of thermal conductivity of duralumin as 150 W/m-K. Answer: 22.833 kJ/minarrow_forwardConsider a closed cylindrical reactor vessel of diameter D= 1 ft, and length L= 1.5 ft. The surface temperature of the vessel, T1, and the surrounding temperature, T2, are 390 deg. F and 50 deg. F, respectively. The convective heat transfer coefficient, h, between the vessel wall and surrounding fluid is 4.0 Btu/h . ft . ⁰F. Calculate the thermal resistance in ⁰F .h/Btu.arrow_forward
- In a multilayered rectangular wall, the thermal resistance of the first layer is 0.005 °C/W, the resistance of the second layer is 0.2° C/W, and for the third layer it is 0.1 ° C/W. The overall temperature gradient in the multilayered wall from one side to another is 70° C. a. Determine the heat flux through the wall. b. If the thermal resistance of the second layer is doubled to 0.4° C/W, what will be its influence in % on the heat flux, assuming the temperature gradient remains the same?arrow_forwardA 2 m X 1.5 m section of wall of an industrial furnace burning gas is not insulated, and the temperature at the outer surface of this section is measured to be 80oC. The temperature of the furnace room is 30oC, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 w/oC. It is proposed to insulate this section of the furnace wall with glass wool insulation (K=0.038 W/moC) in order to reduce the heat loss by 90 percent. Assuming the outer surface temperature of the section remains at about 80oC, determine i) the thickness of the insulation that is needed and ii) the outer surface temperature of the insulation after installation.arrow_forwardA 50-meter-long cast iron pipe with a 10-centimeter outside diameter goes through a 288 K temperature open environment. The temperature of the pipe's outer surface is 423 K, and the combined heat transfer coefficient on the pipe's outside surface is 25 W/m2 K. Considering and stating the necessary assumptions determine, (5 marks) (a) The rate of heat loss from the pipe (b) The energy lost per year if the cost of the fuel is 0.52 $/therm ( 1 therm = 105,500 kJ) c) The thickness of the insulation if 98% of the energy loss is planned to be saved. Consider the conduction coefficient of the insulation is 0.035 W/mK.arrow_forward
- A 30-m-long section of an 8-cm-diameter horizontal hot water pipe passes through a large room whose temperature is 20°C. If the outer surface temperature of the pipe is 70°C, determine the rate of heat loss from the pipe by natural convection. k = 0.02699 W/m °C Pr = 0.7241, ν = 1.749 ×10-5. Select one: a. 3485.4 W b. 3827.7 W c. 2211.8 W d. 2683.6 Warrow_forwardClothing made of several thin layers of fabric with trapped air in between, often called ski clothing, is commonly used in cold climates because it is light, fashionable, and a very effective thermal insulator. So it is no surprise that such clothing has largely replaced thick and heavy old-fashioned coats. Consider a jacket made of five layers of 0.1-mm-thick synthetic fabric (k = 0.13 W/m·K) with 1.5-mm-thick air space (k = 0.026 W/m·K) between the layers. Assuming the inner surface temperature of the jacket to be 28°C and the surface area to be 1.25 m2, determine the rate of heat loss through the jacket when the temperature of the outdoors is 0°C and the heat transfer coefficient at the outer surface is 25 W/m2·K. What would your response be if the jacket is made of a single layer of 0.5-mm-thick synthetic fabric? What should be the thickness of a wool fabric (k = 0.035 W/m·K) if the person is to achieve the same level of thermal comfort wearing a thick wool coat instead of a…arrow_forwardA heating system is to be designed to keep the wings of an aircraft cruising at a velocity of 900 km/h above freezing temperatures during flight at 12,200-m altitude where the standard atmospheric conditions are 55.4°C and 18.8 kPa. Approximating the wing as a cylinder the elliptical cross section whose minor axis is 30 cm and disregarding radiation, determine the average convection heat transfer coefficient on the wing surface and the average rate of heat transfer per unit surface area.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license