F1 A square rod with dimensions 0.02 m x 0.02 m x 0.5 m is attached to a solid surface as shown. If the forces on the rod are too large, it will either crush or be sheared off where it is attached to the solid surface. If the rod can withstand either a maximum normal stress of 25 kPa or a maximum shear stress is 15 kPa, a)what is the largest allowable magnitude of F, (in N) if F,=0? b)what is the largest allowable magnitude of F, (in N) if F,=0? F,

F1 A square rod with dimensions 0.02 m x 0.02 m x 0.5 m is attached to a solid surface as shown. If the forces on the rod are too large, it will either crush or be sheared off where it is attached to the solid surface. If the rod can withstand either a maximum normal stress of 25 kPa or a maximum shear stress is 15 kPa, a)what is the largest allowable magnitude of F, (in N) if F,=0? b)what is the largest allowable magnitude of F, (in N) if F,=0? F,

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

A 9 ft wide and infinitely long flexible strip load of 800 lb/ft2 is placed on an elastic medium as shown in Figure P8.7. Find the vertical stress increase at points A, B, and C located 3 ft below the surface.
5 decimal places 1. At the proportional limit, a certain material has a stress of 78 MPa as the strain is 0.0004. What is the modulus of elasticity of the material in GPa? 2. A 7-ft diameter spherical tank is subjected to an internal pressure of 24 psf. If the wall thickness is 0.35", determine the tangential stress of the wall in psi. A spherical pressure vessel of 5.7 meter diameter is subjected to an internal pressure of 5.0 MPa. Determine the tangential stress (MPa) developed in the wall of the vessel if the thickness is 4 mm.
Q) If the failure of shearing stress in a steel plate is 2,300KN, determine (a) the force required to punch a 32 mm diameter hole in a 10mm thick plate and, (b) the corresponding normal stress ina punch.
A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure. a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN?c. What is the maximum shear stress in MPa?
a)Calculate the stress components acting on the inclined plane AB. b)Calculate prime stresses c)Calculate the maximum shear stress Shear stress = 60 Mpa
Calculate the minimum diameter of cylindrical vessel made of 1-inch thick materials that is use to carry a gas at a pressure of 1500psi. The stress is limited to 12ksi.
A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a solid circular bar. a) Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b) If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? c) Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.
a cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, can only be subjected to a maximum stress value of 120MN/m^2. if the same amount of pressure is applied/ contained in a spherical vessel whose internal volume is 0.075m^3, what must be the sphere's material thickness if it is experiencing a stress value of 127.484 MN/m^2. the radial stress for spherical vessel is theta sub s equals pD/4t
The propeller shaft of a large ship has outside diameter 18in. and inside diameter 12in., as shown. The shaft is rated for a maximum shear stress of 4750psi.a. If the shaft is turning at 100rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress?b. If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12.4 ksi, Sy = 3.5 ksi, and Sxy = 3.6 ksi. Assume B = 29°. Determine the normal stresses ox, and oy, and the shear stress rxy, at the point.
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.
A hollow metal tube with an inside diameter of 265 centimeters must carry a tensile load of 910kN. Determine the outside diameter of the tube, in meters, if the stress is limited to 171 MPa.