Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 18 ksi in the direction shown, determine the magnitude of the maximum in-plane shear stress at the point. 15 ksi 4 ksi O 11.2 ksi O 15.5 ksi O 13.6 ksi 18.6 ksi O 17.3 ksi

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 18 ksi in the direction shown, determine the magnitude of the maximum in-plane shear stress at the point. 15 ksi 4 ksi O 11.2 ksi O 15.5 ksi O 13.6 ksi 18.6 ksi O 17.3 ksi

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.6P: Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in...

See similar textbooks

Similar questions

The stresses shown in the figure act at a point in a stressed body. If σ = 5.8 ksi in the direction shown, determine the shear stress at this point on the inclined plane shown. 5.23 ksi 8.31 ksi 7.76 ksi 7.14 ksi 4.31 ksi
Determine the outside diameter of a hollow steel rod that will carry atensile load of 55,000 kg at a stress of 1,500 kg/cm2 and the wallthickness is 10 mm.A. 8.17 cm C. 12.67 cmB. 8.34 cm D. 7.28 cm
12,5:The two wooden plates are connected to each other with nails as shown in the figure. Since a nail carries a shear force of 1kN with confidence, find the shear P that the joint can carry with the moth. Answer:P=0,89 kN
From the figure, diameter= 22 mm, determine the following:Eccentric load located 2V:H 1. Shear stress due to load alone 2. Most critical rivet 3. Shear stress due to moment alone 4. Maximum shear stress
In Figure 2, the system under the torsional effect;Draw the torsional moment diagram.Determine the torsional angle CA (rotation angle) that will occur at point C.Determine the maximum shear stress that will occur in the system.(G=80 000 MPa)M1(Nm) 9000 M2(Nm)2000 D1(mm) 90 D2(mm) 60 D3(mm) 50 D4(mm) 30
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitude acting on horizontal and veritcal planes at the point are Sx= 12.7 ksi, Sy= 1.7 ksi, Sxy= 5.8 ksi. Assume beta= 34 degrees. Determine the normal stresses and shear stress
The system shown in the figure consists of two bars and is subjected to a force at B and C.[d1 = 53 mm, d2 = 32 mm, L1 = 1.2 m, L2 = 1.3 m, E= 120 GPa, PC = 35 kN, PB = 35 kN] Determine the deformation of rod (2)? Determine the displacement of point C?in mm
The normal stress (kN/cm2) at the K point resulting from the tensile force of P=1000 kN acting from the point B (in the z direction) eccentrically on the I section with dimensions b=30 cm, h=50 cm and t=5 cm shown in the figure below. calculate.
Two elastic bodies made of different materials are placed in a rigid cavity and their surfaces are in full contact. In the vertical direction, a uniform pressure force acts on body 1 with 120MPa and on body 2 with 40MPa. Calculate all the stresses in objects 1 and 2 and the length changes in the z-axis direction.Elasticity modules:E1 =180GPa, E2 =100GPaPoisson ratios:v1 =0.4, v 2=0.2
A solid rectangular object having dimensions of l = 4.00 cm, w = 3.00 cm, and h = 1.00 cm is subjected to a compressive stress having a force of F = 2.00×10⁵ N applied perpendicularly on the right and left faces of the rectangular object. This stress causes compression on the box by Δl = 1.25% of its length as shown in Figure A. The Shear modulus of the rectangular object is just 35% of its Young's modulus. If this force was instead applied on the upper and lower faces on the rectangular object without changing the direction of the force (Figure B), by how much distance would the upper face be deformed with respect to the lower face of the rectangular object?
A plastic beam has a cross section with dimensions of a = 3.8 in., b = 13.3 in., d = 7.6 in., and t = 1 in. The centroid is located c = 3.214 in. above the bottom surface of the beam, and the moment of inertia of the shape about the z centroidal axis is Iz = 247.59 in. 4. For a shear force of V = 1750 lb, what is the maximum shear stress in the beam?
Question 3 (CLO#2) The beam structure shown in Figure 2 below supports a uniformly distributed load of 100 kN/m and a concentrated load of 250 kN. The beam has a box-shaped cross-section with the dimensions provided below. Determine the following: .a) The magnitudes and location of the maximum bending moment and shear force that occur in the beam. .b) The geometric centroid and moment of inertia of the box beam cross-section. .c) The magnitude and location of the maximum bending stress(es) within the beam. .d) Based on your findings from part c), determine which of the following ductile materials would be most appropriate for the design of this beam (considering strength only). Discuss your reasoning. o Material A with yield strength of 175 MPa o Material B with yield strength of 345 MPa o Material C with yield strength of 210 MPa