ZVA @Asiacell lI.Test 3.pdfF1F2aF3Ad.baF4Consider the following values: -F5a = 12 m; b = 10 m; c = 10 m; d = 8 m;F1 = 6 kN; F2 = 7 kN; F3 = 8 kN; F4 = 9 kN; F5 = 10 kN;a = 30°, e = 45°B = 60°1] What is the resultant moment of the five forces acting on the rod about point A?2] What is the resultant moment of the five forces acting on the rod about point B?3] What is the resultant moment of the five forces acting on the rod about point C?4] What is the resultant moment of the five forces acting on the rod about point D?5] What is the moment of the force F2 about point E?6] What is the resultant moment of the five forces acting on the rod about point E?

Consider the following values: - F5 a = 12 m; b 10 m; c 10 m; d 8 m; F1 = 6 kN; F2 = 7 kN; F3 = 8 kN; F4 = 9 kN; F5 = 10 kN; a = 30°, 0 = 45°, B= 60° 1] What is the resultant moment of the five forces acting on the rod about point A? 21 What is the resultant moment of the five forces acting on the rod about point B? 31 What is the resultant moment of the five forces acting on the rod about point C?

Consider the following values: - F5 a = 12 m; b 10 m; c 10 m; d 8 m; F1 = 6 kN; F2 = 7 kN; F3 = 8 kN; F4 = 9 kN; F5 = 10 kN; a = 30°, 0 = 45°, B= 60° 1] What is the resultant moment of the five forces acting on the rod about point A? 21 What is the resultant moment of the five forces acting on the rod about point B? 31 What is the resultant moment of the five forces acting on the rod about point C?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The load on a 2-in.-diameter hydraulic cylinder increases from 10,000 lb to 15,000 lb. Due to the compressibility of the oil, the piston retracts 0.1 in. If the volume of oil under compression is 10 in^3, what is the bulk modulus of the oil in units of kpsi? Enter only a whole number.
please very urgent The bank in the figure is thought that a person is sittingthe force exerted on the board as 300 NIt is given. Elasticity of the boards that make up the benchmodule E = 7 GPa, the width of a board is 150 mm andSince the height is 30 mm, the person sitsCalculate the slump at the point. (Hint: ABas if built-in board A and BThink about it.) Dimensions ar in mm.
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.
Show complete solutions and figures The diameters of the two cylinders A and B in the figure shown are 80 mm and 750 mm, respectively. The face of the piston is 1.2 m above the face of the weight platform. The space in between the piston and the weight is filled with oil (s.g.=0.80). If F=75 N, Determine the following: the value of Wrequired to maintain equilibrium. a) 38.6 N b) 86.3 N c) 63.8N d) 83.6 N e) None
a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and shrunk onto a steel wheel 800.50mm in diameter. The modulus of elasticity of steel is 200gpa. Which of the following most nearly gives the comprehensive pressure between the tire and the wheel? A 3.30 mpa B 3.90 mpa C 3.75 mpa D 4.35 mpa
A thin-walled hollow sphere 3.8 m in diameter holds helium gas at 1767 kPa. Determine the minimum wall thickness of the sphere in mm if its allowable stress is 84.8 MPa.
Dinding ruang penyimpanan berpendingin adalah panjang 10 m dan tinggi 3 m dan dibangun dengan blok beton 100 mm (k = 0.935 W / [m °C]) dan 12 cm papan isolasi serat (k = 0,048 W). / [m °C]). Suhu ruang pendingin -10 °C dan koefisien perpindahan panas konvektif adalah 40 W / (m² K); suhu udara luar adalah 30 °C dengan koefisien pindahan panas konveksi permukaan dinding luar 10 W / (m² K). Hitung koefisien perpindahan panas keseluruhan. Koefisien pindah panas keseluruhan =AnswerW / (m² K).
A thick-wall underwater pipe is placed at 20m below sea level. The pipe is carryingcompressed natural gas with pressure of 50 MPa. The pipe has 115mm outer diameter andmade of 316 stainless steel with yield strength of 205 MPa. The density of sea water could betaken as 1029 kg/m3. Find out:a) What is the resultant outer pressure acting on the underwater pipe? b) What is the minimum inner diameter to ensure the pipe does not yield?c) Sketch the variation of hoop and radial stress across the pipe wall, completed with stresslabelling. d) What is the resultant longitudinal stress of the pipe?
The wires AB and AC are made of steel, and wire AD is made of copper. Before the 150-lb force is applied, AB and AC are each 60 in. long and AD is 40 in. long. If the temperature is increased by 80F, determine the force in each wire needed to support the load. Each wire has a cross-sectionalarea of 0.0123 in2. Take Est = 29(10 3) ksi, Ecu = 17(10 3) ksi, fast = 8(10 6)>F, acu = 9.60(10 -6)>F.
I need to find the forces in each tube but I keep getting stuck. I have been getting really long equations to do algibra onwhich I suspect might be where the error was comming from. The values I have tried are F2 = -0.97786, and -4.889 kips
A cable is tied to a car, which then speeds away. The car and the object to which the cable is tied are considered rigid. The car weighs 3000 lbs. The cable is 100 ft long and has an area of 0.2 in2. If the car is going 5 mph when it reaches the end of the cable, calculate (i) deflectionin the cable, (ii) Stress in the cable, (iii) Max. force in the cable. (Ecable = 12 × 106 psi)
Calcuate Torsion From Point A to Point C and Bending from Point A to Point B and from Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in