F15–12. The cannon and support without a projectilehave a mass of 250 kg. If a 20-kg projectile is fired from thecannon with a velocity of 400 m/s, measured relative to thecannon, determine the speed of the projectile as it leavesthe barrel of the cannon. Neglect rolling resistance.30

Answered: F15–12. The cannon and support without…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 4-kg collar C has a velocity of ?? = 2?/? when it is at A. If the guide rod is smooth, draw a free body diagram and determine the speed of the collar when it is at B. The spring has an unstretched length of ?o =0.2?
The cannon and support without a projectilehave a mass of 250 kg. If a 20-kg projectile is fired from thecannon with a velocity of 400 m>s, measured relative to thecannon, determine the speed of the projectile as it leavesthe barrel of the cannon. Neglect rolling resistance.Show the Free Body Diagram
If the contact surface between the 20-kg block and the ground is smooth, determine the velocity of the block when t = 4 s. Initially, the block is at rest.
The jet discharges water at a rate of 0.10 cu.m/s and at a speed of 18 m/s to the stationary plate. Determine the force on the plate. A. 1800 N B. 2800 N C. 2000 N D. 2500 N
Sand is discharged from the silo at A at a rate of 46 kg/s with a vertical velocity of 10 m/s onto the conveyor belt, which is moving with a constant velocity of 1.5 m/s. The conveyor system and the sand on it have a total mass of 810 kg and center of mass at point G. Neglect the thickness of the conveyor.(Figure 1) 1)Determine the vertical component of reaction at the roller support A 2)Determine the horizontal component of reaction at the pin support B 3)Determine the vertical component of reaction at the pin support B
If the 10-g bullet is traveling at 310 m/s when it becomes embedded in the 11-kg block, determine the distance the block will slide up along the plane before momentarily stopping.
The spring has a stiffness k = 750 N/m and an unstretched length of 50 cm. A 2 kg block is given a speed vA (2 m/s when it is at A, and it slides down the incline having a coefficient of kinetic friction uk = 0.3. Determine the velocity of the block before it touches the spring, the work done by the weight and the friction.
A freight elevator, including its load, has a mass of 1.1 Mg. It is prevented from rotating due to the track and wheels mounted along its sides. If the motor M develops a constant tension T = 6.9 kN in its attached cable, determine the velocity of the elevator when it has moved upward 7.2 m starting from rest. Neglect the mass of the pulleys and cables.
Prob. 14-1 14-2. For protection, the barrel barrier is placed in front of the bridge pier. If the relation between the force and deflection of the barrier is F= (90(10%)x/2) Ib, where x is in ft, determine the car’s maximum penetration in the barrier. The car has a weight of 4000 Ib and it is traveling with a speed of 75 ft/s just before it hits the barrier. F(Ib)
The jet has a speed of 1260 km/hkm/h when it is flying horizontally. Air enters the intake scoop S� at the rate of 52 m3/sm3/s. The engine burns fuel at the rate of 1.85 kg/skg/s, and the gas (air and fuel) is exhausted relative to the plane with a speed of 2330 km/hkm/h. The plane has a mass of 8 MgMg. Assume that the air has a constant density of ρa�� = 1.112 kg/m3kg/m3. (Figure 1) Determine the drag exerted on the plane by air resistance. Express your answer to three significant figures and include the appropriate units.
the particle has a mass of 0.5 kg and is confined to move along the smooth horizontal slot due tot he rotation of the arm OA. Determine the force of the rod on the particle and the normal force of the slot on the particle when theta= 30°. The rod is rotating with a constant angular velocity thetadot = 2 rad/s. assume the particle contact only one side of the slot at any instant
The spring is placed between the wall and the 10-kg block. If the block is subjected to aforce of F = 500 N, determine its velocity when s = 0.5 m. When s = 0, the block is at restand the spring is uncompressed. The contact surface is smooth.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

F15–12. The cannon and support without a projectile have a mass of 250 kg. If a 20-kg projectile is fired from the cannon with a velocity of 400 m/s, measured relative to the cannon, determine the speed of the projectile as it leaves the barrel of the cannon. Neglect rolling resistance. 30