The man stands a distance d from the wall and throws a ball at it with a speed vo. Determine the angle 0 at which he should release the ball so that it strikes the wall at the highest point possible. What is this height? The room has a ceiling height h2. Given: d = 18 m m vo = 15 Vo h2 hi = 1.5 m h2 = 6 m m g = 9.81 -

The man stands a distance d from the wall and throws a ball at it with a speed vo. Determine the angle 0 at which he should release the ball so that it strikes the wall at the highest point possible. What is this height? The room has a ceiling height h2. Given: d = 18 m m vo = 15 Vo h2 hi = 1.5 m h2 = 6 m m g = 9.81 -

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.11P: Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.

See similar textbooks

Similar questions

In a governor of the Hartnell type the arms of the bell-crank leversare equal in length, and those carrying the operating masses arevertical when the governor is rotating at its mean speed of 775rev/min, with the masses moving in a circle of 175 mm diameter -The usual central controlling spring is replaced by two paralleltension springs direetly connecting the operating masses. Find(a) the magnitude of each operating mass if a force of 90 N isrequired at the sleeve to maintain it in the mean speed positionwhen the specd is increased from 775 to 800 rev/m in(b) the stiffness, or rate, of each spring if the ratio of sleevemovement to increase of speed is 1 mm to 10 revImin when inthe mean speed position.
Block A has a weight of 60 lb and block B has a weight of 10 lb. Neglect friction and the mass of the cord and pulleys. The figure shows a system of pulleys and blocks. Block A is located on an inclined surface with a slope of three-fourths. Block B is vertically suspended by a cord that goes over a pulley located at the top end of the inclined surface. The cord then goes downward and to the left, parallel to the slope, then it goes over a pulley fixed to the upper right end of block A. Then the cord goes upward and to the right parallel to the slope. The end of the cord is fixed to the anchor. Determine the speed of block A after it moves 5.7 ft down the plane, starting from rest.
An electric motor M is used to reel in cable and hoist a bicycle into the ceiling space of a garage. Pulleys are fastened to the bicycle frame with hooks at locations A and B, and the motor can reel in cable at a steady rate of 20 in./sec. At this rate, how long will it take to hoist the bicycle 7.9 feet into the air? Assume that the bicycle remains level.
A spring is used to stop the box A which weighs 650 N and is sliding down from an inclined plane with friction and 40 degrees angle. The spring constant is 18 kN/m. The spring is pressed to 3 cm with using wires at the beginning. When the box is L=8 m away from the box, its velocity is V=11 m/s. What is the extra pressed distance of the spring when the box is stopped? The friction coefficient of the plane is 0.22.
The three masses in the figure are different. The planes do not have friction with the masses and the plane of mass 3 corresponds to a quarter of a circumference. All three masses are released at the same time. The masses m2 and m3 travel the same distance. The first mass that will reach the bottom of the ramp will be: m1 m2 m3 m2 and m3 m1 and m2 m1 and m3 they will all arrive at the same time
A spring-based toy gun is used to shoot a ball of mass M straight up.The ball is not attached to the spring. The ball is pushed downward into the spring so that the spring is compressed toa distance S below its relaxation point. After the release, the ball reaches a maximum height 3S,measured from its relaxation position, see Fig. 1(b). (a) Find the constant of the spring. (b) Findthe equilibrium point of the ball when it is on the compressed spring with no forces other than gravity and thespring acting on it. Clearly indicate the point you are using as the origin of your coordinate system and which direction is positive.system and which direction is positive. (c) Now the ball is glued to the spring so that it oscillates up and downinstead of flying off the spring. The spring is again compressed to the same distance S below itsof relaxation. Write an equation for the position of the ball as a function of time after it is released. Indicateclearly which point you are using as the origin…
A 12-lb weight stretches a spring 2 ft. The weight is released from a point that is 1 ft below the equilibrium position with an upward velocity of 4 ft s-1.
Situation 02. A crate has a mass of 120kg and the coefficient of static and kinetic frictionis 0.60 and 0.50, respectively. The crate starts from rest and the motor exerts a tensionT= 1220 + 200t (N). If the elevation of the dock is 30 degrees from the horizontal,a. What is the velocity of the crate after 1sec?b. Compute the power transmitted after 1sec.
The speed of the engine mechanism shown in Figure 1 is controlled by the Porter governor. All arms of the governor are 20 mm and are hinged at a distance of 4 mm from the axis of rotation. The mass of each ball is 100 g and the mass of the sleeve is 500 g. The governor sleeve begins to rise at 40 rad/s. when the links are at an angle of 5° to the vertical. Assuming the friction force to be constant: 3.1. Draw the port governor mechanism and clearly lable it. (06)3.2. Calculate the minimum speed of rotation (in rad/s) when the inclination of the arms to the vertical is 10°.
Forming a shock absorber, two springs of equal length are nested together. If the maximum compression of the springs is 0.25 and the outer spring has a stiffness of Ka = 420 N/m, what stiffness is required of the inner spring Kb? The design of the spring system is such that if a mass of 2.5 kg is at rest, then dropped from a distance of 0.75 m above the springs, the spring system will catch and stop the mass.
The elevator E and its freight have a total mass of 400kg. Hoisting is provided by the motor M and the 150-kg block C. If the motor has an efficiency of ε =0.85, determine the power that must be supplied to themotor when the elevator is hoisted upwards at aconstant speed of VE = 4 m/s. Please show every single step of the process and the free body diagrams thanks
A 3.00 kg low friction cart sits on a horizontal surface. At each end, there is a spring of force constant 100 N/m attached to a firm support. The cart starts at rest at the equilibrium position. A quick blow of a hammer delivers an impulse of 0.50 N-s to the cart. (a)How long will it take for the cart to return to the equilibrium position? (b) How much energy is delivered to the cart by the impulse of the hammer? (c) How far will the cart travel before returning to the equilibrium position?