Figure 1 shows a diver ready to take off at the end of diving board. The board is supported by rollers andpins, which allow vertical displacement but withstand axial loads and moments. If the diver weighs 58kgand the board is 2.8m long, determine the maximum slope and deflection at the end of the platform.Assumed that EI is constant and gravitational acceleration is 9.81m/s.0.5mFigure 1

A beam is said to be cantilever beam if is fixed from one end and free from another. A beam is said…

Figure 1 shows a diver ready to take off at the end of diving board. The board is supported by rollers an pins, which allow vertical displacement but withstand axial loads and moments. If the diver weighs 58k and the board is 2.8m long, determine the maximum slope and deflection at the end of the platform Assumed that EI is constant and gravitational acceleration is 9.81m/s². 0.5m Figure 1

Figure 1 shows a diver ready to take off at the end of diving board. The board is supported by rollers an pins, which allow vertical displacement but withstand axial loads and moments. If the diver weighs 58k and the board is 2.8m long, determine the maximum slope and deflection at the end of the platform Assumed that EI is constant and gravitational acceleration is 9.81m/s². 0.5m Figure 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The deflection angles of two intermediate points R and S on the curve measured from the tangent passing through the P.C. are 6o15’ and 12o15’ respectively. The chord distance between R and S is 20 m. while the long chord is 100 m. meters long. Compute the radius of the curve Compute the angle of intersection of the simple curve. Compute the tangent distance
A uniform beam that 10-m long is being supported by two men, one man at each end. The weight of the beam. Is 100-N. If the first man supporting at the right side exert twice as much as the second man on the left, where must a 50-N motor be placed (measured from the first man) on top of the beam? Show complete solution.
Determine the deflection curve, the length, and the maximum tension in theuniform cable shown below. The cable has a weight per unit length weightof ω0 = 12 N/m.
A 4.8 m-long from fixed point, 0.5 m wide and ssumed a thickness of 30 mm troughout a springboard made of high strengh S-2 glassfiber material which weighs 3.6-kN/m. If a diver impacts 30-kN at the free-end of the board when about to dive, calculate: i. the reaction at the fixed-end of the cantilever and bending moment diagram. ii. the maximum bending moment in the beam. if the material Young's Modulus of elasticity is 93.8 GPa find: iii the maximum slope of the beam. iv. the maximum deflection in the beam. v. the maximum strength in the material
Find the slope and deflection equations for the beam shown. Determine the rotationfrom point C. The unit of measure "t" means ton, 1 ton = 9.81 kN. Loaddistributed is vertical, downwards. EI = constant. Double Integration Method.
consider the beam shown in. EI is constant. assume that EI is in kip * ft2. determine the expression for the elastic curve using the coordinate x1 for 0 < x1 < 20 ft, where x1 is in feet. v1 in ft answer in terms of the variables x1, E and I. determine the expression for the elastic curve using the coordinate x2 for 0 < x2 < 10 ft where x2 is in feet. v2 in ft. answer in terms of the variables x2, E and I. specify the deflection of the beam at C. vc in ft. answer in terms of E and I. specify the slope at A, measured counterclockwise from the positive x1 axis. Theta A in rad. answer in terms of E and I.
A spring sustains 200 ft-lb of energy with a deflection of 3’’. Assume that the mean coil diameter is 7 times the wire diameter and that the allowable stress is 100ksi. Determine the wire diameter.
A cable with supports at the same elevation has a span of 550 ft. The cable weighs 4 lb / ft and the sag at midspan is 100 ft. Determine The length of the cable.
Pls answer thank you! A helical spring having squared and ground ends has a total of 20 coils and its material has modulus of elasticity in shear of 78.9 Gpa. If the spring has an outside diameter of 10.4 cm and a wire diameter of 0.625 cm, compute the deflection in the spring due to a load of 50 kgs.
The homogeneous AB beam weighs 400 lbs. For each support condition in (a) a (d), plot the DCL of the beam and determine the number of unknowns.
1. A cable used to lift heavy materials can resist breaking even under a load of 1 meganewtons. The steel cable must support twice that load for safety purposes. By how much the steel cable will stretch if it carries 1 meganewtons of load? Assume 8.0 m initial length of the cable. 2. Ships and sailing vessels often carry lead ballast in various forms, such as bricks, to keep the ship properly oriented and upright in the water. Suppose a ship takes on cargo and the crew jettisons a total of 0.500 m3 of lead ballast into water 2 000 m deep. Seawater's density is equal to 1.025 g/cc while lead's bulk modulus equals to 42.0 GPa. Calculate the weight of water in a column with cross section of 1.00 m2. Find the change in the pressure at 2.0 km depth. Find the change in the volume of the lead at 2.0 km depth.
The beam shown in Fig. a supports the triangular distributed loading. Determine its maximum deflection. EI is constant.