Figure 5 shows a lever ABC pivoted at B and having a mass of 6 kg and a grinding radius of 75 mm at B. The lever GDF has a uniform section pivoted at G and has a mass of 1.2 kg. It carries a mass of I kg in F. The ECD chain has a mass of 1 kg and always moves on a vertical axis. It carries a mass of 1kg in E. K1 and K2 spring has a constant of 400 N/m and 1 kNm, Find the natural E 50 mm C A K2 200 mm 300 mm 50 mm G F 350 mm 100 mm- frequency of the system. Ignore all pendulum effects. [Ans: 14.68 rad/s]

Figure 5 shows a lever ABC pivoted at B and having a mass of 6 kg and a grinding radius of 75 mm at B. The lever GDF has a uniform section pivoted at G and has a mass of 1.2 kg. It carries a mass of I kg in F. The ECD chain has a mass of 1 kg and always moves on a vertical axis. It carries a mass of 1kg in E. K1 and K2 spring has a constant of 400 N/m and 1 kNm, Find the natural E 50 mm C A K2 200 mm 300 mm 50 mm G F 350 mm 100 mm- frequency of the system. Ignore all pendulum effects. [Ans: 14.68 rad/s]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A four wheeled trolley car has a total mass 3000kg. Each axle with its two wheels and gears has a total moment of inertia of 32kgm2. Each wheel is of 400mm radius. The centre distance between the two wheels on an axle is 1.4m. Each axle is driven by a motor with a speed ratio of 1.3. Each along with it gear has a moment of inertia of 16kgm2 and rotates in the opposite direction to that of the axle. The centre of mass of the car is 1m above the rails. Calculate the limiting speed of the car when it has to travel around a curve of 250m radius without the wheels leaving the road.
In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is tobe as close as possible to 220 mm and the teeth are to have a module of 4. When the ringis stationary, the spider, which carries three planets, is to make one revolution for everyfive of the driving spindle carrying the sun wheel.(a) Determine suitable numbers of teeth for all the wheels. 10(b) Determine the exact p.c.d of the ring 2(c) If a torque of 12 Nm is applied to the shaft carrying the sun wheel, what torquewill be required to keep the ring stationary?
Fast pls solve this question correctly in 5 min pls I will give u like for sure Aka a=200mm B=250mm c=20mm determine the moment of inertia about the x axis
The variation diagram of the cutting force of the cutting work done with the press shown in the figure is given in the figure. Engine speed is 1400 rpm, flywheel speed is 75 rpm. The moment of inertia of the rotating masses in the engine is 0.75 kgm^2. Calculate the flywheel moment of inertia required for the press so that the velocity unevenness is 0.02. It is known that the engine power is 2 kW.
The two cranks of an inside cylinder locomotive are at right angles and the distance between the cylinder centre lines is 0·625 m. The stroke of the pistons is 0·6 m and the revolving parts that have to be balanced are equivalent to 300 kg at the centre of each crank pin. The cylinders are symmetrically placed between the driving wheels, which are 1·5 m apart. Find the magnitude and angular positions of the balance masses required in the planes of the driving wheels at a radius of 0·8 m.
A gear engine automobile is traveling along a curved track of 120m radius. Each of the four wheels has a moment of inertia of 2.3 kg m2 and an effective diameter of 600 mm. The rotating parts of the engine have a moment of inertia of1.25kg m2 the gear ratio of the engine to back wheel is 3:2.The engine axis is parallel to the gear axle and the crank shaft rotates in the same sense as the road wheels. The mass of the vehicle is 2050 kg and the center of mass is 520 mm above the road level. The width by the track is 1.6m, what will be the limiting speed of the vehicle if all the four wheels maintain contact with the road surface (b) Explain the function of a flywheel from a crank effort diagram.
1-)The diagram of the change of cutting force for the cutting work performed with the press seen in the figure is given in the figure Engine revthe number is 900 rpm and the number of Flywheel revolutions is 60 rpm.The moment of inertia of the rotating masses in the engine is 0.35 kgm^2. Speedcalculate the moment of Flywheel inertia required for the press so that its smoothness is 0.01 . Engine power is 1.5 kWit is known
The length of the connecting rod of a gas engine is 400 mm and its centre of gravity lies at 120 mm from the crankpin centre. The rod has a mass of 80 Kg and a radius of gyration of 182 mm about an axis through the centre of mass. The stroke of piston is 225 mm and the crank speed is 300 rpm. Determine the inertia force on the crankshaft when the crank has turned 30 ° from the inner dead centre.
The diagram shows a torque angle diagram for a certain machine. The speed of the shaft must be maintained between 490 and 510 RPm. determine 1) greatest fluctuation in energy 2) moment of inertia of the suitable flywheel 3) the mass required if the radius of gyration is 0.3m
Please show graphical method representation for all questions a b and c. please.... Thank you A shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: The magnitude of the mass in plane E and its angular position relative to the mass in plane A The distance of the plane E from plane A The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the…
A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at a rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm². If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate : 1.Mass of the flywheel having radius of gyration of 1.5 m
Calculate the moment of inertia, Izz, of the simple crankshaft in the figure below. The material has a density of 7700kg/m3. All the round parts have a diamter of 50mm. All diamensions is in millimeters. Both ends are 60mm in length.