B7 please solve for all of the members and thereforces. state whether they are in compressionor tensionK5ftAA 54 65ft5ft5ft F 5AF SA G501b30ft*all angles are45° except right anglesーま。

Answered: Image /qna-images/answer/97782492-8ca2-432b-b9fe-9f912bc63134.jpg

Answered: please solve for all of the members and…

please solve for all of the members and there forces. state whether they are in compression or tension K 5ft 2. 5ft 5ft F SA 8 F SA G 501b 30ft Fall angles an 45° except right angles _一ミー

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 415 kg safe is hanging from the apparatus below. Determine the tension in the cable. Dimension a=1.9 m and dimension b=2.5 m. The mass of the beam is 85 kg. Use g = 10 N/kg. Hint: Take torques about the hinge and use the perpendicular lever arm version of the torque equation (the sin theta version will work but will require more calculation).
1 ! SHOW COMPLETE SOLUTION ! * DRAW FBD *pls answer manually Problem 1: The pulleys are frictionless and of negligible weight A 250 kg 300 kg C B 450 kg Find: A. Tension (N) in the cord supporting block B. B. Acceleration at Block A (m/s^2) C. Acceleration at Block B (m/s^2) D.Acceleration at Block C (m/s^2)
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.
A ladder carried by a fire truck is 20.0 m long. The ladder weighs 3400 N and its center of gravity is at its center. The ladder is pivoted at one end (A) about a pin (Fig. ); ignore the friction torque at the pin. The ladder is raised into position by a force applied by a hydraulic piston at C. Point C is 8.0 m from A, and the force F S exerted by the piston makes an angle of 40° with the ladder. What magnitude must F S have to just lift the ladder off the support bracket at B? Start with a free-body diagram of the ladder.
The cable carrying three 400-N loads has a sag at C of hC = 14 m. Calculate the following: 26.1 The magnitude of the tensile force in segment AB is Blank 1 N. 26.2 The magnitude of the tensile force in segment BC is Blank 2 N. 26.3 The magnitude of the tensile force in segment CD is Blank 3 N. 26.4 The magnitude of the tensile force in segment DE is Blank 4 N.
Hi! Help me with this please. This is under Statics of Rigid Bodies. Thank you so much! A 500-kg block is resting on a 30º inclined plane with fs = 0.30. Find the required force P acting horizontally that will prevent the block from sliding. PLEASE CORRECT ANSWER.
The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
Consider a uniform ladder of length 4.3 m and mass 10 kg. The ladder is falling over, pivoting about the end that is touching the ground. Someone is pushing on the top end of the ladder with a horizontal force of size 415 N. At the instant when the ladder makes a 46 degree angle with the horizontal, calculate the net torque on the ladder about its bottom end, in N m. Make your answer positive, and use g = 10 m/s2. (Please answer to the fourth decimal place - i.e 14.3225)
Dont copy from chegg The disc brakes at the front of a car have pistons of 1582 mm2 cross-sectional area each, whereas the drum brakes at each of the rear wheels have pistons of 300 mm2cross-sectional area. The master cylinder has piston of 582 mm2 cross-sectional area.Determine the total force applied at the front and rear brake cylinders and the ratio in
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
I need to find the forces in each tube but I keep getting stuck. I have been getting really long equations to do algibra onwhich I suspect might be where the error was comming from. The values I have tried are F2 = -0.97786, and -4.889 kips
The 0.4 kg B pin in the figure moves freely inside the circular slide DE with radius b and the counterclockwise (positive direction) rotating arm OC. Calculate the radial (Fr) and axial (Fθ) forces using the values in the table, ignoring friction. b=211 mm θ=19 θ.=9 rad/s θ..=285 rad/s2