Figure P6.6 Unity feedback system. P6.6 A unity-feedback control system is shown in Figure P6.6 O. Determine the relative stability of the system with the following loop transfer functions by locating the complex roots in the s-plane: 10s + 2 a. Ge(s)G(s) 82 (s + 1) 24 b. G.(8)G(s) = s(s3 + 10s? + 35s + 50) (s + 2)(s + 3) s(s + 4)(s + 6) c. G.(s)G(s) =

Figure P6.6 Unity feedback system. P6.6 A unity-feedback control system is shown in Figure P6.6 O. Determine the relative stability of the system with the following loop transfer functions by locating the complex roots in the s-plane: 10s + 2 a. Ge(s)G(s) 82 (s + 1) 24 b. G.(8)G(s) = s(s3 + 10s? + 35s + 50) (s + 2)(s + 3) s(s + 4)(s + 6) c. G.(s)G(s) =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A) Write the equation for the small-signal gain function Vout/Vinfor the followingop-amp circuit B) What kind of filter is this circuit? C)Write the equation for the cutoff frequency of the filter D) Sketch the Frequency Response of the system
An uncompensated unity feedback system with certain deficiencies has no zeroes and poles at -1, -2 and -5. Answer the following questions based on the above description of the system Determine using an apt technique, the gain of the system at damping ratio 0.45
a) Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. b) Define the gain and phase margin, this time on the nyquist curve.
WHAT IS THE IMPORTANCE OF SECONDARY CIRCUIT AND IMPULSE COUPLING?
Figure P4.12 shows the asymptotic Bode plot of a filter we wish to use to reduce the gain over a band of frequencies. Design a circuit that realizes the given frequency response. Give the schematic, and indicate element values chosen for your design, knowing that there are plenty of 5 KOhm, 10 KOhm , and 20 KOhm resistors available in the stock room.
A unity feedback system with forward transfer function below G(s) = K/(s(s+6)).is operating with a closed-loop step response that has 15% overshoot. Please solve for the following:a. Evaluate the settling time. b. Evaluate the steady-state error for a unit ramp input. c. Design a lag-lead compensator to decrease the settling time by 2 times and decrease the steady-state error for a unit ramp input by 10 times. Place the lead zero at -3.
Consider the circuit shown in Figure P6.23.Determine the resonance frequency and the bandwidthfor the circuit.
Simplify the system shown in Figure Q1(b) to a single transfer function
a) Explain the drawing rules and formulas of the Nyquist curve. b) G(?)=K [(S−1)(S−2) / (S+2)(S+3)] ; Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. c) Define the gain and phase margin, this time on the nyquist curve.
Figure shows a low-pass filter; the output voltage is taken across the capacitor in an L-R-C series circuit. Derive an expression for Vout/Vs, the ratio of the output and source voltage amplitudes, as a function of the angular frequency ω of the source. Show that when ω is large, this ratio is proportional to ω-2 and thus is very small, and show that the ratio approaches unity in the limit of small frequency.
Find an expression fro the gain if Rin = infinity, Rout = 0, and Ao does not equal infinity.
Determine the overall transfer function for the system as shown in Figure Q4.