ON 01Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mmthat is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is ahollow section with an internal diameter of di = 60 mm. An external torque T, = 10 kN.m isapplied at point D.(a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm.(b) What is the maximum angle of twist, aand where does it occur?-635 mm--635 mm-|AToВ•Dd,

Answered: Image /qna-images/answer/8a4b6f8c-8147-48dc-ae53-310ee34af579.jpg

Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of d. = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque To 10 kN.m is %3D applied at point D. (a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm. (b) What is the maximum angle of twist, aand where does it occur? -635 mm -635 mm A To В •D Td, -X-

Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of d. = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque To 10 kN.m is %3D applied at point D. (a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm. (b) What is the maximum angle of twist, aand where does it occur? -635 mm -635 mm A To В •D Td, -X-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.8P: A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque...

See similar textbooks

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
The steel axle of a large winch on an ocean liner is subjected to a torque of 1.65 kN · m (see figure). What is the minimum required diameter dminif the allowable shear stress is 48 M Pa and the allowable rate of twist is 0.75º/m? (Assume that the shear modulus of elasticity is 80 G Pa.) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d/8, Compare dminvalues to corresponding values from part (a)
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
Two sections of steel drill pipe, joined by boltedflange plates at B, are being tested to assess the adequacyof both the pipes. In the test, the pipe structureis fixed at A, a concentrated torque of 500 kN ? m isapplied at x = 0.5 m, and uniformly distributed torqueintensity t0 = 250 kN . m/m is applied on pipe BC.Both pipes have the same inner diameter d = 200 mm.Pipe AB has thickness tAB =15 mm, while pipe BChas thickness tBC =12 mm. Find the maximum shearstress and maximum twist of the pipe and their locationsalong the pipe. Assume G = 75 GPa.