Figure Q6 (b) shown four bar linkages system, where crank length is 6.25 cm, connecting rod length is 17.5 cm and follower length is 20 cm. Crank and follower are grounded with distance 20 cm at flat surface. If the crank rotates clockwise at 100 rpm, find angular velocity of connecting rod and follower when the crank angle 60° to the flat surface.

Figure Q6 (b) shown four bar linkages system, where crank length is 6.25 cm, connecting rod length is 17.5 cm and follower length is 20 cm. Crank and follower are grounded with distance 20 cm at flat surface. If the crank rotates clockwise at 100 rpm, find angular velocity of connecting rod and follower when the crank angle 60° to the flat surface.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the degree of freedom of mechanism given below,
For the given mechanism, mechanical advantage for the configuration given is?
draw kinematic diagram of following mechanisms 4, 5 and 6 and calculate their degree of freedom
Q2BCQ4 is a four bar linkage. Q2 and Q4 are fixed centers on a horizontal line 10 inches apart. Q2B is a link 5 inches long oscillating about Q2. Q4C is a crank 2 ½ inches long which rotates about Q4. BC is a connecting rod 11 ½ inches long. Q2 is left of Q4. A link, EF 6 inches long is pinned to Q2B at E, 1 ½ inches from B. Another link GF 3 ½ inches long is pinned to link BC, 4 inches from C. These links EF and GF are pinned together at F in their upper position. Trace the paths of the points F and G while Q4C makes 1 complete revolution. Find points for each 15 deg position of Q4C and any other necessary in order to secure smooth curve
Design a quick return mechanism with 2400 mm stroke, time of forward stroke is 3s,return stroke time is 1s, fixed link length of 50 cm and driving crank length of 80cm.Determine a.Range of values of L2b.α and βc.ϕ1 and ϕ2d.Actual value of L2
Find the degree of freedom of the mechanism shown below,
For the mechanism shown in Figure P3.13 (a) Draw the velocity polygon (1 in = 10 in/sec) (b) Specify velocity of points: B, C, D Specify angular velocity of links: 3, 4
Figure P3.40 illustrates a pendulum with a base that moves horizontally. Thisis a simple model of an overhead crane carrying a suspended load with cables.The load mass is m, the cable length is L, and the base acceleration is a(t).Assuming that the cable acts like a rigid rod, derive the equation of motion interms of ? with a(t) as the input.
Figure Q3(b) shows a uniform bar AB of mass = 8 kg hinged at point C. Point A is connected to a spring to maintain the bar in vertical direction, and the stiffness k = 500 N/m. If point A is displaced counter-clockwise by a small angle θ = 3.5 degree and released, (i) With the free body diagram and kinetic diagram, determine the initial horizontal displacement of A.
Consider two robot-manipulators:• A SCARA robot with joints displacement range q1,2 = −90◦...90◦ and q3 = 0..10cm and links lengths L1,2=10 cm.• A Cartesian robot with joint displacements’ range q1,2,3 = 0..10 cm.Which statement is correct?1) The Cartesian robot has a larger workspace.2) It is not possible to judge the workspace based on the information provided.3) Both robots have revolute joints.4) The SCARA robot has a larger workspace.
For the scotch yoke mechanism shown in the figure P4.1, the horizontal position of link 4 canbe described as x = 3 cos (50t + 40°). Determine the displacement of link 4 during theinterval of 3.8 to 4.7 s.
Given: AB = 0.1 m , CB = 0.4 m, CD = 0.6 m, AD = 0.8 m For the linkage shown below, CD moves back and forth spinning flywheel AB, link CD is the input link. a.) Find the maximum angle in degrees, that is the angle between the extreme positions by the link CD when the circle AB rotates 360 degrees? b.) Why is the wheel able to rotate fully and not get locked up when CD and AB are inline (collinear)? Where's a real life example where this mechanism may be used?