Fill in the blanks: The volumes of states 1, 2 and 3 of a diesel cycle operating on an air standard are 300 cm3, 2 x 10-5 m3 and 60 cm3, respectively. Find the power output if the heat input is 120 kW. **Express final answer to the NEAREST WHOLE NUMBER. Do not round off in between solution. Type only the "numerical value". No need to include the unit and percent sign. Answer: kW Previous Continue >

Fill in the blanks: The volumes of states 1, 2 and 3 of a diesel cycle operating on an air standard are 300 cm3, 2 x 10-5 m3 and 60 cm3, respectively. Find the power output if the heat input is 120 kW. **Express final answer to the NEAREST WHOLE NUMBER. Do not round off in between solution. Type only the "numerical value". No need to include the unit and percent sign. Answer: kW Previous Continue >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thermodynamics (Brayton Cycle) Round up the answer up to 5 decimal places. A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following: a. Pressure & temperature at each stateb. T-S diagramc. Heat Added, per unit massd. Thermal Efficiencye. Mass flow rate, kg/min
Completely solve and box the final answers. Write legibly 2. There are required 2.5 MW from a gas turbine unit for pumping of oil. Air enters the compressor at 1.02 bar and 9.2°C. The discharge pressure is 1020kpa. The turbine section receives the hot gases at 820°C. For a Brayton cycle, determine the required air flow in kg/minute.
HANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution.ANSWER iii. Consider an ideal gas with the following characteristics: R = 115 ft-lbf/lbm-R Cp = 0.25 + 0.00035T (BTU/lbm-R) i. Solve for the value of k at 1250 R. ii. Refer to the table shown below: SEE IMAGE iii. Solve the following unknown parameters for Carnot cycle: Volume at end of isothermal compression Heat added and Heat rejected Wnet Efficiency Mean effective pressure iv. Solve the following unknown parameters for Otto Cycle Mass Pressure and Temperature ateach corner Heat added and Heat rejected Wnet Efficiency Mean effective pressure Percentage clearance v. Solve the following unknown parameters for Diesel Cycle with 6% cut-off. Compression ratio Percentage clearance Heat added and Heat rejected Wnet Efficiency Mean effective pressure
Thermodynamics (Jet-Propulsion Cycle) Round up the answer up to 5 decimal places. A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure & temperature is found to be 14.7psi & 546R. The axial flow compressor provides a pressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of air inside the engine is 133 lbm/s. Determine the following: a. T-S diagram b. Pressure & temperature at each state c. Thrust force (lbf)
In a standard Brayton cycle, the maximum temperature is 1,478 K while the minimum temperature is 301 K. The heat added during the isobaric process is 966 kJ/kg. Determine the thermal efficiency in %. Use two decimal places in the final answer.
Use the steam tables provided and use 4 decimal places for solving. In an idealRankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to a pressure of 10 kPa. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.) Findthe quality of the steam,Qa, Qr, Wt, Wp, Wnet, efficiency, and steam rate
The following parameters are recorded on a gas turbine test rig. Stage-1: Inlet temperature is 5000C, Inlet pressure is 650kPa. Exit gas pressure 150kPa. Determine the exit gas temperature for isentropic process. Stage-2 Gas is again heated to 4500C by constant volume process. Assume R=287 J/kg.K; Determine the heat added to the gas assuming Cp/Cv=1.4 and Cp/Cv=1.3; Draw the T-S diagram for the above process.
32 - A fixed volume insulated tank, initially empty, was connected to a distribution line carrying helium gas at 115ºC by means of a valve. The valve is opened first and closed when the pressure is the same as the distribution line pressure. What is the final internal energy of helium in the tank? (Internal energy of the warehouse in the final state = Enthalpy of the distribution line). (Cp=5.1926) will be taken. a) 2014.7 kJ/kg B) 649.1 kJ/kg NS) 2118.6 kJ/kg D) 2066.7 kJ/kg TO) 597.1 kJ/kg
Thermodynamics Instructions: Determine the following for the CYCLE a) Work b) Thermal efficiency c) steam rate *show complete solutions and please write legibly. TY
Read carefully. Please solve ellaborately and include the untis in every step, and write your solutions clearly and readable if your solution is in written form, Your work will be appreaciated much. Thank You! The following data were obtained during performance test with a simple open cycle gas turbine engine: compressor inlet temperature, 520*R; compressor isentropic discharge temperature, 672"R; actual compressor discharge temperature, 691"R; turbine inlet temperature, 1500 R; turbine isentropic discharge temperature, 1184"R; and turbine actual discharge temperature, 1216°R. For these conditions calculate the thermal efficiency in percent.
Air undergoes a Carnot cycle inside a piston-cylinder between thermal reservoirs at 1200K and 400K. During heat addition, the volume triples. what is the overall cycle efficiency? Group of answer choices 57.45% 67.66% 66.67% 65.65%
Thermodynamics (Brayton Cycle) Round up the answer up to 5 decimal places. A 120 MW gas turbine power plant running on Ideal Brayton cycle has the following initial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature at the turbine entrance is 910°C. Determine the following: a. Pressure & temperature at each state b. T-S diagram c. Heat Added, per unit mass