Homework Help is Here – Start Your Trial Now!
Math
Statistics
Filling Time 60 Degrees 1 0.2438 1 0.2613 1 0.4985 2 0.2486 2 0.3110 0.5205 0.5523 1.0395 1.3801 223 2 3 3 72.5 Degrees 85 Degrees 0.2528 0.2512 0.2528 0.2512 0.2529 0.2510 0.2449 0.2544 0.2681 0.2542 0.4903 0.2902 0.2999 0.2468 0.8882 0.2497 1.2200 0.2995

Filling Time 60 Degrees 1 0.2438 1 0.2613 1 0.4985 2 0.2486 2 0.3110 0.5205 0.5523 1.0395 1.3801 223 2 3 3 72.5 Degrees 85 Degrees 0.2528 0.2512 0.2528 0.2512 0.2529 0.2510 0.2449 0.2544 0.2681 0.2542 0.4903 0.2902 0.2999 0.2468 0.8882 0.2497 1.2200 0.2995

Algebra & Trigonometry with Analytic Geometry
Algebra & Trigonometry with Analytic Geometry
13th Edition
ISBN:9781133382119
Author:Swokowski
Publisher:Swokowski
Chapter2: Equations And Inequalities
Section2.1: Equations
Problem 70E
See similar textbooks
icon
Related questions
Question

Referring to Table 2, the mean square for the factor filling time is____

1). 0.9030

2). 0.4234

3). 0.4515

4). 0.2117

Filling Time 60 Degrees 1 0.2438 1 0.2613 1 0.4985 2 0.2486 2 0.3110 0.5205 0.5523 1.0395 1.3801 223 2 3 3 72.5 Degrees 85 Degrees 0.2528 0.2512 0.2528 0.2512 0.2529 0.2510 0.2449 0.2544 0.2681 0.2542 0.4903 0.2902 0.2999 0.2468 0.8882 0.2497 1.2200 0.2995
Transcribed Image Text:Filling Time 60 Degrees 1 0.2438 1 0.2613 1 0.4985 2 0.2486 2 0.3110 0.5205 0.5523 1.0395 1.3801 223 2 3 3 72.5 Degrees 85 Degrees 0.2528 0.2512 0.2528 0.2512 0.2529 0.2510 0.2449 0.2544 0.2681 0.2542 0.4903 0.2902 0.2999 0.2468 0.8882 0.2497 1.2200 0.2995
TABLE 2 A plastic injection molding process is often used in manufacturing because of its ability to mold complicated shapes. An experiment was conducted on the manufacture of a television remote part, and the warpage (mm) of the part was measured and stored in TVRemote. (Data extracted from M. A. Barghash and F. A. Alkaabneh, "Shrinkage and Warpage Detailed Analysis and Optimization for the Injection Molding Process Using Multistage Experimental Design," Quality Engineering, 26, 2014, pp. 319-334.) Two factors were to be considered, the filling time (1, 2, or 3 sec) and the mold temperature (60, 72.5, or 85° C). ■ You need to download file "TVRemote". TARIE 2
Transcribed Image Text:TABLE 2 A plastic injection molding process is often used in manufacturing because of its ability to mold complicated shapes. An experiment was conducted on the manufacture of a television remote part, and the warpage (mm) of the part was measured and stored in TVRemote. (Data extracted from M. A. Barghash and F. A. Alkaabneh, "Shrinkage and Warpage Detailed Analysis and Optimization for the Injection Molding Process Using Multistage Experimental Design," Quality Engineering, 26, 2014, pp. 319-334.) Two factors were to be considered, the filling time (1, 2, or 3 sec) and the mold temperature (60, 72.5, or 85° C). ■ You need to download file "TVRemote". TARIE 2
Expert Solution
steps

Step by step

Solved in 3 steps with 3 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Recommended textbooks for you
Algebra & Trigonometry with Analytic Geometry
Algebra & Trigonometry with Analytic Geometry
Algebra
ISBN:
9781133382119
Author:
Swokowski
Publisher:
Cengage
Elementary Algebra
Elementary Algebra
Algebra
ISBN:
9780998625713
Author:
Lynn Marecek, MaryAnne Anthony-Smith
Publisher:
OpenStax - Rice University
Linear Algebra: A Modern Introduction
Linear Algebra: A Modern Introduction
Algebra
ISBN:
9781285463247
Author:
David Poole
Publisher:
Cengage Learning
SEE MORE TEXTBOOKS