Q1/ A gas turbine cycle has the following working parameters:- The pressure of air entering the compressor at( 1 bar)The compressor ratio=6- Max. Temperature of cycle (1000°k) and Min. temperature (288 °k )-Nc= 0.85. NT=0.9Find :1) Nth 2)Net work per kg

Answered: Image /qna-images/answer/8ca06bd7-a9c3-4497-b092-0624c18c81b1.jpg

Answered: Find :1) Nth 2)Net work per kg

Engineering

Mechanical Engineering

Find :1) Nth 2)Net work per kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.) In an ideal Brayton cycle, air enters the compressor section at 14.7 psia and 55°F. The pressure ratio is 12. Turbine inlet condition of 1300°F. Draw the P-V and T-S diagrams and determine the following: a. Pressure, specific volume & temperature at each state b. Compression ratio c. Work, per unit mass
Question 4 A single acting two stage reciprocating compressor takes in air at a rate of 0.2 m3/s at a pressure of 0.1 MPa @ 16˚C. The air is compressed to 0.7 MPa while running at 600 rpm. Compression is ideal and the process follows pV1.25 = C. Perfect intercooling takes place and neglecting clearance. What is the Intermediate pressure (IP) in kPa .............., the volume of the Low-Pressure cylinder in m3................... , the volume of the High-Pressure cylinder in m3.................. and the Total Cycle Power (TCP) in kW .....................
Air enters the compressor of a Brayton cycle, having a pressure ratio of 12. The initialconditions of the air are; 15 psi & 90°F. Hot air enters the turbine with a temperature of2200 R. 20ptsDetermine the following:a. Turbine work, in BTU/lbmb. Efficiency
The volume ratios of compression and expansion for a diesel engine as measured from an indicator diagram are 16 and 8 respectively. The pressure and temperature at the beginning of the compression are 1 bar and 28°C. Assuming an ideal engine, determine the mean effective pressure, the ratio of maximum pressure to mean effective pressure and cycle efficiency. Also find the fuel consumption per kWh if the indicated thermal efficiency is 0.5 of ideal efficiency, mechanical efficiency is 0.8 and the calorific value of oil 42000 kJ/kg. Assume for air : cp = 1.005 kJ/kg K ; cv = 0.718 kJ/kg K, ã = 1.4. Please also draw the PV diagram.
An ideal Diesel engine operates on 1.5 lb of air with a suction state at 14.1 psia and 100 F. The pressure at the end of compression is 475 psia and the cut -off is 6% of the stroke from head -end dead - center. Using air properties (R=53.34 ft-lbf/Ibm-R, k=1.4, Cp =.24, Cv=. 1714 Btu/lbm-R), determine compression ratio, percentage clearance, Qa, Qr, Thermal Efficiency, mean effective pressure.
A Brayton cycle with an air inlet temperature of 17 °C has a pressure ratio of 16. While the cycle produces 14 MW of energy, there is an input of 960 kJ/kg 1 heat into the cycle. Recognizing that specific heats change with temperature; a) Find the highest temperature (K) of the cycle. b) Find the compressor work (kJ/kg). c) Find the turbine work (kJ/kg).
Q1/ Ideal reheat cycle, has the following specifications: Boiler pressure is 200 bar and Condenser pressure is 0.22 bar and Reheat pressure is 60 bar , Turbine inlet temperature is 500 C and Reheat temperature 480 C Calculate: quality at turbine exist, thermal efficiency, and steam rate.
An engine works on an Otto cycle. It has a compression ratio of 10.5, and the intake conditions of air are 1 bar, 28°C. Heat added under constant volume is 900 kJ/kg. Find the pressure and temperature at salient points, air-standard efficiency, and mean effective pressure. Assume for air Cv=0.718 kJ/kg.K, and γ =1.4 and R=0.287 kJ/kg.K. Represent the cycle in p-v and T-s diagrams
A Brayton cycle with an air inlet temperature of 17 °C has a pressure ratio of 16. While the cycle produces 14 MW of energy, there is an input of 960 kJ/kg 1 heat into the cycle. Recognizing that specific heats change with temperature; a) Find the highest temperature (K) of the cycle. b) Find the compressor work (kJ/kg). c) Find the turbine work (kJ/kg). d) Find the mass flow rate (kg/s) of the air. e) Calculate the thermal efficiency of the cycle.
1. Compare and evaluate the actual and ideal thermal efficiencies and back work ratio 2. Construct efficiency vs. pressure ratio plot, showing the region of typical values of gasturbine operating pressure ratios.3. What is the main limitation associated with turbine in a gas turbine power cycle.
Given a Brayton cycle, with a pressure ratio equivalent to 12, as shown in the figure, determine its thermal efficiency, in %. Use Standard Cold Air Assumption Method (constant specific heats at room temperature, 25ºC).
A Closed Brayton Cycle operates with 15kg/s of air. Air at the beginning of compression is at 25°C. Pressure ratio is 11. Highest temperature in the cycle is 600°C. SOLVE FOR: a.) Determine the Thermal Efficiency of this cycle in (%) b.) Determine the amount of heat added to the cycle in (kJ/s) c.) Determine the work net of the cycle in (kW) ANSWERS SHOULD BE ROUNDED IN SIX SIGNIFICANT FIGURES