Answered: A 3.0-inch wall of fire brick, k = 8.0…

A 3.0-inch wall of fire brick, k = 8.0 Btu / (ft)(hr) (F/ in) has one surface at 335°F, the other at 80°F. Find the heat conducted through an area of 1.4 ft2 in one d

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.63P

See similar textbooks

Related questions

Q: 56. The inner surface of a 2 inch wall is 70C and its outside surface temperature is 34C. Determine…

A: To find : The steady state heat transfer rate. Given data : The thickness of wall is b=2 inch1 ft12…

Q: A truncated cone 30 cm high is constructed of aluminum. The diameter at the top is 7.5 cm, and the…

Q: The temperature distribution across a wall 1m thick at a certain instant of time is given as T(x) =…

A: Given data, The temperature distribution equation is T=a+bx+cx2…

Q: 1. A flat plate is supplied with a constant heat flux of 100 [W/m²] from bottom. The plate has 0.5m2…

Q: A spherical interplanetary probe of 0.5 m diameter contains electronics that dissipate 150 W. If the…

A: Given DataD=0.5mε=0.8E=150W

Q: A plate made of mild steel having 10 cm thick, maintaining temperature 250°C. The convection &…

Q: The ratio of heat flow through walls A and B (Q/Qµ) having the same thickness having thermal…

A: Given, Relation between thermal conductivities of A and B : kA = 4 kB Relation between temperature…

Q: 0.60W / m•º C _7. A brick wall is 5.0 m long, 3.0 m high, and 30 cm thick. The conductivity of brick…

Q: 1. Find the heat transfer per unit area through the composite wall in Figure below. Assume…

Q: A house, for cooling purposes, consists of two zones: the attic area zone A and the living area zone…

A: Solution: Given Data: K1 = 1/4 K2 = 1/8

Q: The wall of a house, 7 m wide and 6 m high is made from 0.3 m thick brick with k=0.6 W/m.K. The…

Q: XIV- NTC and PTC are where the first with negative and second one with positive coefficient. a)…

A: Problem is based on basic electrical and can be solved as

Q: Two components of a steam engine are shown in the figure below. The turbine is adiabatic. a.…

Q: In a furnace, the inner and outer sides of the brick wall (k1 = 2.5W/mK) are maintained at 1100°C…

Q: 4. A refrigerator is used to cool 4 litres of soft drink from room temperature (23 °C) to 4 °C. If…

Q: An automobile cooling system holds 16 L of water. How much heat does it absorb if its temperature…

Q: Q1) Prove that the equation for one dimension unsteady state conduction with heat

A: For 1-D unsteady state conduction with heat generation is given by...

Q: Part A How much heat is exhausted to the cold reservoir by the heat engine shown in (Figure 1)?…

A: Given data: Q1=90 JQ2=225 J Need to determine the heat exhausted to the cold reservoir by the heat…

Q: A 50 kg weighted foodstuff with a specific temperature of 3.18 kj / kgK is heated in an oven by…

Q: Consider a wall consisting of two layers, A and B, with the following properties: = 1.5 W/m.K; LA =…

Q: b. A slab of stone of area (3600 + R) cm² and thickness 10 cm is exposed on the lower surface to…

A: Draw diagram of slab for better understanding

Q: Qi: (50 marks) Find the total heat flux of the composite wall when: KA = KC = KF = 15 m. K KB = KD =…

Q: A metallic container of fixed volume of 2.5 × 10−3 m3 immersed in a large tank of temperature 27 °C…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Numerical Exercise 1. A flat plate is supplied with a constant heat flux of 100 [W/m²] from bottom.…

A: 1. A flat plate is supplied with a constant heat flux of 100 [W/m²] from bottom. The plate has 0.5m²…

Q: Consider a wall consisting of two layers, A and B, with the following properties: kA = 1.5 W/m.K; LA…

Q: k = 150 N/m P = 50 N 50 cm www 1 A kg 30° p = 0.1 110 cm www A kg

Q: 300 kJ of thermal energy is stored at a temperature of 1000 K. Assuming perfect heat transfer to a…

Q: Carnot refrigerator operates between reservoirs at -20∘C∘C and 40 ∘C∘C in a 25∘C∘C room. The…

Q: energy can be conserved when your home heating/cooling system works less during the heating and…

A: Assumptions necessary to make this statement (regarding energy conservation) valid for cooling and…

Q: If I have a simple piston-cylinder heat engine, where air is the working system and constant heat is…

A: Given: Piston cylinder heat engine system. Since wall are not insulated, so heat transfer doesn't…

Q: An office space of 15 ft x12 ft x10 ft height. The heat loss through walls is (6949.8 Btuh) if…

A: An office space of 15 ft x12 ft x10 ft height. The heat loss through walls is (6949.8 Btuh) if…

Q: The height of a cylindrical tank, containing 20 lb of gas at 70 psia and 140 deg. F is 2.5 times its…

Q: Q2/ A plane wall generates heat internally at the rate of 0.2 MW/m' with 8.0 cm thick. One side of…

Q: A flat plate, maintained at 250 C is placed vertically in air at a pressure of 1 bar and temperature…

A: Write the given data. P=1 barTs=250 °CT∞=20 °Cb=10 cmd=20 cm

Q: A house has walls made out of steel with the following properties: Thickness Density Thermal…

A: Given, density , ρ = 7800 Kg/m3 thickness , x = 300mm thermal conductivity , k =50 W/m-k…

Q: Heat flows through a composite slab, as shown below. The depth of the slab is 1 m. The k values are…

Q: relation between the heat capacity of a plate (q) and time (t). If the relation between the leachate…

Q: The total heat gain through a roof (4 in concrete with 2 in insulation, U roof=0.4 Btu/ hr. ft2 F),…

A: Given that, Total heat gain through a roof=7112 BtuhU=0.4 Btu/hr·ft2°FTout=105 °FTin=75…

Q: Question:The northerm east wall of cold storage warehouse is 965 ft^2 the outside surface of the…

A: Given data :- Area of wall, A = 965 ft2 Wall U factor = 0.06 Btu/…

Q: A crucible of molten metal at 1800°C is placed on the foundry floor. The foundryman covers it with a…

A: Refer next sheet for the answer.

Q: A thin board of 0.5 cm thickness is exposed to a fluid of T, = 22°C and h = 30 W/m².K from one side…

Q: A truncated cone 30 cm high is constructed of aluminum. The diameter at the top is 7.5 cm, and the…

A: Given Data: The height of the truncated cone is h = 30 cm. The diameter of the top is d = 7.5 cm…

Q: A slab of stone of area (3600 + R) cm² and thickness 10 cm is exposed on the lower surface to steam…

A: The area of the slab is given by, The temperature of the steam is given by, The specific latent…

Q: 2. A steel plate of k=50W/mK and thickness 10cm passes a heat flux by conduction of 25kW/m2. If the…

Q: A refrigerator has a coefficient of performance of 2.50, requires 150 W of electrical power to…

Q: Heat Transfer A wall of an oven with a wire in it. Across the wire a voltage of 50 Volts and a…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

100%

A 3.0-inch wall of fire brick, k = 8.0 Btu/ (ft)(hr) (CF/ in) has one surface at 335°F, the other at 80°F. Find the heat conducted through an area of 1.4 ft? in one day.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A plane wall, 7.5 cm thick, generates heat internally at the rate of 105 W/m3. One side of the wall is insulated, and the other side is exposed to an environment at 90C. The convection heat transfer coefficient between the wall and the environment is 500 W/m2 K. If the thermal conductivity of the wall is 12 W/m K, calculate the maximum temperature in the wall.
An air-cooled condenser has an h value of 30 W/m2-K based on the air-side area. The air-side heat transfer area is 190 m2 with air entering at 27°C and leaving at 40°C. If the condensing temperature is constant at 49°C, what is the air mass flow rate in kg/s? Let Cp(air) = 1.006 kJ/kg-K. Draw and label the temperature-flow diagram. Round off your answer to three (3) decimal places.
A creamy must cool 20,000 liters of milk received each day from initial temperature of 32℃ to a final temperature of 1℃ in 6 hours. If refrigeration losses amount 12 percent of the cooling load, what must be the capacity of the refrigerating machine? Note: Specific heat of milk if 3.9 kJ/kg-K and S.G. = 1.05.
Find the rate of heat transfer if the cylinder in a stainless steel rod.k = 15 W/m·K (8.7 Btu/h·ft·F), L = 1 m (3.3 ft), Th = 200 C (392 F), Tc= 100 C(212 F), A = 5 cm2 (0.8 in2).
Find the amount of heat lost per hour through a square foot ofbuilding wall composed of 18-in. sandstone and 3/4-in. metal lath andplaster separated by a 1 1/4-in. air space, when the temperature of theroom is 70 °F, the outdoors is 10 °F, and the wind velocity is 15 mph.
In the United States, energy for household heating is generally sold using English units, e.g., therm, gal, and cord. A house in Wisconsin uses 1200 therms of thermal energy during the heating season. Calculate the cost of fuel if the furnace uses (a) natural gas with an efficiency of 70%; (b) No. 2 fuel oil, efficiency 65%; (c) kerosene, efficiency 99.9% (unvented); and (d) wood with l5% moisture with an efficiency of 50%. Use the data in Tables 2.2, 2.7, and 2.13. The efficiencies are based on the HHV. Assume the cost of natural gas is $8/MBtu, the cost of No. 2 fuel oil is $3/gal, the cost of kerosene is $3.50/gal, and the cost of wood is $100/cord. Assume the bulk density of cord wood is 30 lbm/ft3 .
An office heater puts out 2090 Btu (British thermal units) of energy in the form of heat per hour. Given that 1 Btu=1.055 kJ,how many megajoules of energy in the form of heat can be produced per year (365 days) by the heater, assuming continuous operation?
Heat transfer by conductivity: One side of a 3 cm thick copper plate is held at 400°C and the other at 100°C. How much head transferred through the plate?
A truncated cone 30 cm high is constructed of aluminum. The diameter at the top is 7.5 cm, and the diameter at the bottom is 12.5 cm. The lower surface is maintained at 93°C; the upper surface, at 540°C . The other surface is insulated. Assuming one dimensional heat flow, what is the rate of heat transfer in watts?
give a specific example of a process that has the energy changes and transfers described. (For example, if the question states “ΔEth > 0, W = 0,” you are to describe a process that has an increase in thermal energy and no transfer of energy by work. You could write “Heating a pan of water on the stove.”) ΔEth < 0, W ≠ 0, Q ≠ 0
A truncated cone 30 cm high is constructed of aluminum. The diameter at the top is 7.5 cm, and the diameter at the bottom is 12.5 cm. the lower surface is maintained at 93 o C; the upper surface, at 540 o C. The other surface is insulated. Assuming one dimensional heat flow, what is the rate of heat transfer in watts?
Air at 27 Celsius degree receives heat at a constant volume until its temperature reaches 927 Celsuis degree. determine the heat added per kelogram?