Find (a) the velocity and total acceleration of the point 0.3 meters from the center of Disk E, as shown, at t = 0.67345 seconds. Also, (b) determine the number of revolutions done by Disk E at the same time. Given motor shaft I, from rest, it rotates to achieve a counterclockwise angular velocity, w; = (0.13t³ + 3.32t² ) rad/s and no slippage occurs within the system.

Find (a) the velocity and total acceleration of the point 0.3 meters from the center of Disk E, as shown, at t = 0.67345 seconds. Also, (b) determine the number of revolutions done by Disk E at the same time. Given motor shaft I, from rest, it rotates to achieve a counterclockwise angular velocity, w; = (0.13t³ + 3.32t² ) rad/s and no slippage occurs within the system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

257 / 5000 Wyniki tłumaczenia The water jet leaves the impeller of the centrifugal pump at a speed of 25 m/s and an acceleration of 30 m/s 2, measured against the impeller along the AB line.Determine the speed and acceleration of the water jet at point A. The rotor is rotating at an angular speed of 15 rad/s.
Pumps: Two geometrically similar pumps are running at the same speed of 1000 rpm. One has the impeller diameter of 0.4 m and discharge of 30 liters/sec against a head of 20 m. If the other pump gives half of the discharge rate, then determine the head and diameter of the second pump. Answer: D=0.317 m, H=12.6 m
As a young engineer, you have been tasked to select the location of a wind turbine based on the details of the location and relevant specification below:Air densityAverage air velocityDiameter of wind turbine bladesLOCATION A1.29 kg/m3 54 km/h 70 mLOCATION B1.21 kg/m3 63 km/h 60 m By comparing the amount of power generated (in MW) at Location A and Location B, determine the location that will give the optimum wind power generation.9 kg of Refrigerant 134-a is initially at 26.69°C with enthalpy of 100 kJ/kg. Heat is transferred to the refrigerant under a constant-pressure process until the entropy of the refrigerant reaches 0.9795 kJ/kg.K.(i) Determine the final temperature of the refrigerant(ii) Calculate the boundary work, Wb, in kJ.Assist your answer with a proper P-v diagram indicating the properties,process, and boundary work region clearly.(iii) Explain the reason behind the high amount of boundary work obtained in (ii).Assist your explanation with relevant sketching.
At a hydraulic plant the propeller type turbine are rated at 48,000 HP at 82 rpm under a 14 meters head, the diameter is 7 meters, for a geometrical similar turbine to develop 36,000 HP under a 11 meters head. After resolving the percentage change in probable flow, determine the following: (A) What diameter, in meter, of the impeller to be used? (B) What is the speed, in RPM, should be used?
A radial flow pump whose 100-mmmm-diameter impeller rotates at 120 rad/srad/s discharges water at 0.25 m3/sm3/s. Determine the discharge of a geometrically similar pump having a 155-mmmm-diameter impeller that rotates at 90 rad/srad/s. Express your answer to three significant figures and include the appropriate units.
6 Adımlı problem tekniğini kullanın. tanımlama, veri, teori, tahmin etme, çözme, doğrulama. lütfen bu tekniği kullanın
A stroke of a reciprocating engine is 600 mm. neglecting the effect of angularity of the connecting rod, find a) velocity in m/s of the piston , b) acceleration of the piston in m/s^2 when the crank is 30 degree past TDC. The engine is running at 720 rev/min tools : r=1/2 stroke, v=wrsin theta! a=wr^2costheta
plz ansswer q1 part e velocity is in km/h not in m/s
For the tutorial question, assume the inputs are: A = 0.75 [m] ; B = 1.03 [m] ; C = 0.685 [m] ; U = 33.5 [km/hr]; ANSWER: 1A) In the gradient equation of the keel L(z) = A + B · z; A = 1B) and B = 2) If Re_CR = ρ · U · L_CR; then L_cr [m] = 3A) To determine D_S, one needs first to calculate C_f_l(z). In the equation C_f_l(z) = D / l(z)^(-0.2) + E / l(z); D = 3B) and E =
Calculate the displacement, the real power and the real torque of an hydraulic power engine with a theoretical power of 1.5 kW. The rotation speed is 1000 rpm and the pressure is 12 Mpa. Volumetric efficiency is 95% and mechanical efficiency is 93%. Answer :Real power = 1.33kWActual torque = 12.7 N-mDisplacement = 7.12 cm3/rev
The axial flow pump produces a discharge of 0.095 m3/sm3/s. The impeller is rotating at ωω = 110 rad/srad/s, and it has a mean radius of 75 mmmm. (Figure 1) Figure 1 of 1 Part A Determine the magnitude of the velocity of the water as it exits the blades. Express your answer to three significant figures and include the appropriate units. V2V2 = nothingnothing SubmitRequest Answer Part B Complete previous part(s) Part C Determine the magnitude of the relative velocity of the water as it flows off the blades of the impeller. Express your answer to three significant figures and include the appropriate units. (Vrel)2(Vrel)2 = 4.27ms
A water pump dissipates power on the shaft N=5.5 kW. Refine parameters: Head, flow and efficiency of the pump. Knowing the residual pressure Pair = 20, open the pump outlet (head) and the vacuum pressure at the inlet Pa,= 4m (head). The velocity in the thrust tube v2=4 m/s, the ejector tube diameter 75 mm, the suction pipe diameter 100 mm and the difference between the vacuum gauge and the manometer zero. Kinetic correction factor, geometry (Z2) -Z0). Ignore the height POST