Can I have a detailed, step-by-step explanation for the following question? Thank you! Suppose a pitot tube is desired to measure the velocity q of a stream ofwater (take density as p). Then the inner tube BA is placed upstream offlow. The outer tube contains holes such as H. Let P be the pressure in thestream where the fluid velocity is q. Then P is also the pressure on theinside and outside of the hole and hence at D. Let P, be the pressure at C.Considering the stream entering the tube, find q (take density of mercuryas o).H-Mercury

GIVEN: velocity of water stream is 'q' manometric difference between D and C is 'h' Po - P = αgh let…

Answered: find q (take density of mercury H B H…

Engineering

Mechanical Engineering

find q (take density of mercury H B H DE Mercury

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A2 A Newtonian fluid with viscosity (Mu) flows upward at a steady rate between two parallel plates that make an angle y with the horizontal. The fluid thickness h is much smaller than the width of the channel W. The pressures at each end, P(0) and P(L), are known and the pressure variations in the y-direction are small. Assume that Vy and Vz = 0 and Vx is a function of y alone. Use the shell balance to approach : - the Total flowrate, QV
Figure 1) shows a tank of 20∘C water with a nozzle h = 27 cm below the surface. Bernoulli's equation applies to the flow between points 1 and 2 on the streamline, but not to the flow between points 2 and 3.What is the volume flow rate through the nozzle in L/min ? Assume that the water level in the tank is held constant.
Find an expression for the velocity of water leaving the sprinkler. Find an expression for the gauge pressure at point A, a distance L1, upstream of the narrow pipes. Express the answer in terms of the flowrate, Q. The inner diameter of the first segment of the pipe is d1=10mm, the inner diameter of the second set of pipes is d2=1mm, with N=25. The flowrate through the sprinkler is Q=0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds 2000. Comment on the accuracy of the assumption that the flow could be treated as laminar everywhere. May be assumed water has a density of 1000kg/m^3 and a viscosity of 1mPa s.
Suppose your bicycle tire is fully inflated, with an absolute pressure of 7.00 X 105 Pa (a gauge pressure of just under 90.0 lb/in2) at a temperature of 18.0oC. What is the pressure after its temperature has risen to 35.0oC? Assume that there are no appreciable leaks or changes in volume.
TOPIC: FLUIDS AT REST AND MOTION Water flows through a horizontal pipe with a diameter of 4 cm at a speed of 6 m/s with apressure of 400kPa at point A. At point B, the diameter is 2 cm. (a) What is the speed of water at point B. (b) Calculate the pressure at point B. Please help me solve this problem with complete solution. Please include an illustration. Thank you tutor!
Chlorine gas enters a 30-mm ID pipe at 15 m/s, and exits a wider pipe, at 85-mm ID. What is the average velocity through the exit pipe (in m/s)?
Aiming a 1.69 in diameter garden hose straight up, forms a “bubbler fountain” that you could easily drink from (but you shouldn’t because of bacteria, etc.). The water flows out the hose and down the sides. If the water has a density of 63.1 lbm/ft^3 and a viscosity of 0.0119 g/cm*s, what is the thickness of the water film (df) (in cm) if the flow rate of water is 6.42 in^3/s? For simplicity, assume the film is thin enough that you can use rectangular coordinates.
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
Consider the inviscid, incompressible flow of air along a streamline. The air density along the streamline is 0.002377 slug/ft3, which is standard atmospheric density at sea level. At point 1 on the streamline, the pressure and velocity are 2116 lb/ft2 and 10 ft/s, respectively.Further downstream, at point 2 on the streamline, the velocity is 190 ft/s. Calculate the pressure at point 2. What can you say about the relative change in pressure from point 1 to point 2 compared to the corresponding change in velocity?
Water at 20°C flows through the orifice in Fig. ,which is monitored by a mercury manometer. If d = 3 cm,(a) what is h when the flow rate is 20 m3/h and (b) what isQ in m3/h when h = 58 cm?
mechanical fluid A crude oil of kinematic viscosity 0.4 stoke is flowing through a pipe of diameter 300 mm at the rate of 300 litres per sec. Find the head lost due to friction for a length of 50 m of the pipe.
at point a in pipeline carrying water, the diameter is 1m, the pressure is 98kPa and the velocity is 1m/s. at point B, 2m higher than A, the diameter is 0.5m and the pressure is 20kPa. Determine the direction of flow. need answer please