Find the factor of safety of the post BD using the langer-static criterion, i need the answer please Two forces are applied to an AISI 1050 HR post BD, as indicated. Knowing that thecross section of the vertical part of the post is 1.5 X 2.4 in.,1- Find the state of stress for the most critical point on the round shaft (i.e., point H)2- build the mohr's circle at point H.3- Apply the failure theories to find the factor of safety.4-Calculate the total strain energy in the post BD.5-Find the deflection of point C using Castigliano's theorem in the direction of force 500Ib.6-Find the factor of safety of the post BD using the langer-static criterion,7-Draw the the langer static criterion and locate the load line.6000 lbZ4 in.1 in.y1.5 in.3.25 in.DB2.4 in.1.75 in.H500 lb6 in.

Here are the steps needed to use the Langer-static criterion to determine the post-BD safety…

-Find the factor of safety of the post BD using the langer-static criterion, Draw the the langer static criterion and locate the load line. 6000 lb 4 in. 1 in. I I 1.5 in. 3.25 in. B 2.4 in. D 1.75 in. H 500 lb 6 in.

-Find the factor of safety of the post BD using the langer-static criterion, Draw the the langer static criterion and locate the load line. 6000 lb 4 in. 1 in. I I 1.5 in. 3.25 in. B 2.4 in. D 1.75 in. H 500 lb 6 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A 4 m thick steel plate initially at 225 °C. Suddenly, both surfaces are exposed to an ambient at 25…

A: The Biot numberThe Biot number (Bi) is a dimensionless quantity used in heat transfer calculations.…

Q: The 6.4-lb force is applied at point A of the crank assembly. Determine the moment of this force…

Q: Determinn the setillest dimension d that will prevent the dam hom overturning about is end A.

A: GivenThe density of concrete is The density of the water a=1 mh=8 mConsider, The length of the…

Q: shear stress on the key

A: power (P) = 175hp = N=1500RPMd=5Infind shear stress on the key -

Q: The total number of independent equations of equilibrium that we can write for a frame or machine…

A: Six independent equations of equilibrium that we can write for a frame or machine.Option first is…

Q: (5) A 3/4-in-thick steel bar, to be used as a beam, is welded to a vertical support by two fillet…

Q: A pump is driven by an electric motor through a open type flat belt drive. Motor pulley diameter…

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A: Given: The diameter of rod is .The diameter of hole is .The plate thickness is .The head diameter of…

Q: Draw the shear and moment diagram using Moment-Equation Method.

A: considering cross-section X-X at a distance x from point AThe shear force equation at x-section X-X…

Q: Is the frame determinate or indeterminate? Support your answer.

A: According to the given dataA frame is provided. We need to findthe frame is the frame determinate or…

Q: two plates each with thickness t = 16 mm are bolted together with 6-22 mndia. bolts forming alap…

A: 1.The thickness of each plate, t = 16 mmThe spacing between bolts, S1 = 40 mm, S2 = 80 mm, and S3 =…

Q: A sheet of water of uniform thickness (h = 0.02 m) flows from the device shown in the figure below.…

Q: Q5/ Let f(x) = 3√3x. Consider the portion of the curve where 0 ≤ y ≤ 2. Find the surface area of the…

Q: determine the angular acceleration a of the wheel.

A: Now torque can be calculated by using following formula,Explaination;Torque is defined as product of…

Q: The maximum permissible recoil distance of a gun is specified as 0.5 m. If the initial recoil…

A: The given data as below: maximum permissible recoil distance of a gun = 0.5 minitial recoil velocity…

Q: By using equations,show and explain why power required by compressor is higher when temperature at…

A: To analyze the power required by a compressor when the temperature at induction is higher than the…

Q: Determine the applied torque at the circular cross-section having a diameter D = 60 mm, if the…

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 18 mm. Assume…

Q: 3-5. Calculate the moment about point A in Figure P3-5. 800 lb A 4 5' 3 FIGURE P3-5 200 lb 4 | 7' 3'…

A: Moment about a point is the product of force and the perpendicular distance between the line of…

Q: Concentrated loads of Px = 43 kips, Py = 29 kips, and P₂ = 52 kips are applied to the cantilever…

A: The concentrated load, Px = 43 kips, Py = 29 kips, Pz = 52 kipsThe dimensions, a = 7 in, b = 14 in,…

Q: An object is left to cool down in air and the following temperature data were recorded during the…

A: t (min)T (°C)0100188282372470565

Q: 4) Calculate the moment of inertia Ix for the shaded area given below. Ay 10 cm r=10 cm 19 ➤x

Q: Water flows through a 200-mm diameter pipe at a velocity of 1 m/s. Find its flow rate in m^3/min

A: Given that:Diameter of pipe, D=200mmvelocity of water, V=1 m/sTo determine:flow rate, Q

Q: 3. Find the work W required to pump the water out of the pool in the figure below. Assume that the…

A: The height to be pumped, h = 1 foot

Q: Learning Goal: To use the equilibrium equations to solve for unknown forces in a coplanar force…

Q: Air at 20 °C flows with a velocity of 10 m/s along a 4 m flat plate which is maintained at uniform…

A: Given Data as below:To determine:Local heat flux

Q: Q1. A screw jack with a 1-in. double-thread Acme screw is used to raise a load of 4000 N. A plain…

A: Given data as below:diameter=1inLoad = 4000 Ncollar mean diameter = 50 mmcoefficient of friction =…

Q: A copper wire of length 1.80 m and diameter 0.80 mm is suspended from two points, 1.0 m apart and at…

A: For thew figure below following data is providedLength of the copper wire Dia of the wire mass of…

Q: Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive…

Q: The car stops at a distance of Im.

A: Given DataA car of speed VA=74 Km/hA bicycle speed B VB=11m/sThe distance d =44 m from the…

Q: A limited amount of water in a container is subjected to 5 W/m²K convection condition as the sky…

A: Heat transfer coefficient (h) = 5 W/m2kSky temperature = -40oCEmissivity Freezing temperature of…

Q: Draw the sectional view of the solid and provide necessary dimensions. E 7 Scale 1:2 Draw the…

A: According to the given datatwo object views are givenWe need to draw the section view of the problem

Q: 3. For the continuous beam shown, determine the support reactions at pin support A, and roller…

A: The load at mid of B and C, P = 400 lbThe load at AB, w = 80 lb/ft

Q: Find the forces generated in the child in all three axes (r, θ, z). The weight of the child is m =…

Q: A helical compression spring is fabricated from ASTM A229 oil-tempered wire (Figure 14.3a) and has…

A: Note:Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: In the figure, one end of a uniform beam of weight 150 N is hinged to a wall; the other end is…

Q: We want to measure the revolution of an electric motor as in the figure. We tie a steel ball with a…

Q: A cylindrical rod of Ni 200 alloy has the following properties: E = 204 GPa, ν = 0.31. It is loaded…

A: Given data:The modulus of elasticity, E = 204 GPa.The Poisson’s ratio, ν = 0.31.The load is, P =…

Q: I need a KPI for The project consists of two parts The first is glasses that monitor objects…

A: 1. The first is glasses that monitor objects around them, and alert the person when an object is…

Q: B-Write (True) or (False) for the following sentences: 1. Cast-cobalt Alloys tool are produced by…

A: to Write (True) or (False) for the following sentences:Cast-cobalt Alloys tool are produced by…

Q: A square lamina (each side equal to 2m) is submerged vertically in water such that the upper edge of…

A: Given Data

Q: 50 kNm -1.2 m- 70 kNm -1.6 m- D 10 kNm -1.2 m B I W200 X 19.3 Draw the shear-bending moment diagram…

Q: Find frequency and mode shape for the system shown in Fig. 5, using Stodola process. Take m = 1 kg;…

A: The mass, m = 1 kgThe stiffness, k = 1000 N/m

Q: Two horizontal slabs measuring 0.8 x 1 m form the top of one of the slabs. The gap between them is…

Q: Suppose that P₁ = 24 kN, P₂ = 26 kN, and P3 = 30 kN. (Figure 1) Figure 3m 3 m- m B P₁ -3 m- C P₂ -3…

Q: A 0.4 kg rubber ball has a horizontal velocity of 1.554 m/s at point A and goes through a projectile…

A: According to the given dataWe need to findThe velocity of the ball when hits the ground

Q: The polymer bar shown in the figure below has a width of b = 58 mm, a depth of d = 92 mm, and a…

A: Width of b = 58 mmDepth of d = 92 mmHeight of h = 282 mmCompressive load of P = 120kNThe bar height…

Q: Find the eigenfrequency and normal Coordinates for the model below. 47 1 b سید 3₁ 19₂2 олишини と 30

A: Given:To find:Frequency

Q: A moment and four forces are applied to a two-dimensional frame as shown in figure below. Replace…

A: The given figure shows the moment and four forces are applied to a two-dimensional frameTo…

Concept explainers

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.

Question

Find the factor of safety of the post BD using the langer-static criterion, i need the answer please

Two forces are applied to an AISI 1050 HR post BD, as indicated. Knowing that the
cross section of the vertical part of the post is 1.5 X 2.4 in.,
1- Find the state of stress for the most critical point on the round shaft (i.e., point H)
2- build the mohr's circle at point H.
3- Apply the failure theories to find the factor of safety.
4-Calculate the total strain energy in the post BD.
5-Find the deflection of point C using Castigliano's theorem in the direction of force 500
Ib.
6-Find the factor of safety of the post BD using the langer-static criterion,
7-Draw the the langer static criterion and locate the load line.
6000 lb
Z
4 in.
1 in.
y
1.5 in.
3.25 in.
D
B
2.4 in.
1.75 in.
H
500 lb
6 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Setting up the boundaries

VIEW

Step 2: Factor of Safety calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The aluminum (E=15x10^10psi, α=11.6x10^-6/°F) shell is fully bonded to the brass (E=10.6x10^6psi, α=12.9x10^-6/°F) sore, and the assembly is unstressed at a temperature of 78°F. Considering only axial deformations, determine the stress when the temperature reaches 180°F (a) in the brass core (b) in the aluminum shell
Question- 1) Two gage marks are placed exactly 270 mm apart on a 10-mm-diameter aluminum rod with E = 72 GPa and an ultimate strength of 150 MPa. It is Know that the distance between the gage marks is 270.28 mm after a load is applied, determine the stress in the rod
The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α= 10.5 × 10−6/°F] rod (1) and a solid 1.49-in.-diameter bronze [E = 15300 ksi, v = 0.15, α= 7.6 × 10–6/°F] rod (2). Assume L1=11 in., L2=22 in. If the supports at A and C are rigid and the assembly is stress free at 16°F, determine:(a) the normal stresses σ1, σ2 in both rods at 213°F (positive if tensile, negative if compressive).(b) the displacement uB of flange B (positive if to the right, negative to the left).(c) the change in diameter Δd1 of the aluminum rod.
Kindly give right answer other wise don't attempt Determine the maximum stress produced in a rectangular plate 50 mm wide, 8 mm thick with a central hole of 10 mm. It is loaded in an axial tension of 1 kN. Answer-7.813N/MM2
A 5-mm thick, 100-mm wide AISI 1020 steel rectangular plate has a central elliptical hole 8 mm in length transverse to the applied stress and 2 mm in diameter along the stress. Determine the applied load that causes yielding at the edge of the hole. Ans. 92.43 kN
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares, each with a cross-sectional area of 340 mm2. bar (1) has a length L1 = 810 mm and bar (2) has a lenght L2 = 1080 mm. Assume dimensions of a = 480mm, b = 38mm, and c = 600mm. If the allowable normal stress in bars (1) and (2) must be limmited to 165 MPa each, determine: a) the maximum load P that may be applied at D to the rigid bar. b) The deflection at D for the load determined in part (a).
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)
If the principal stresses are of opposite signs, then failure occurs in the plane. True or false?
At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 139°C. Determine the normal stress in the aluminum rod.
2. A steel wire 30 ft long, hanging vertically, supports a load of 500 lbf. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 20,000 psi and the total elongation is not to exceed 0. in. Assume E = 29 × 106 psi.
A steel wire is 6 m long, hanging vertically supports a load of 2000 N. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 4 mm. E=200,000 MPa