If the difference between tight and slack side for a leather belting doesnot exceed100 N/cm of width for a belt 0.5 cm thick. Find the maximum stress in the belt.Consider.angle of lap = 170°Belt speed%3D1000 m/min%3Ddensity of leather = 10-3 kg/cm³Coefficient of friction0.25%3D

Given data; T1-T2= 100 Nb= 1cm =0.01 mt =0.5 cm=0.005 mθ= 1700=170×π180=2.967 radv= 1000…

Answered: Find the maximum stress in the belt.

Engineering

Mechanical Engineering

Find the maximum stress in the belt.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Related questions

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11633 N force. - 540…

A: P= 11633 N Width of the cross section, b= 60 mm Height of the cross section, h= 180 mm

Q: the state of stress at points A and B, and show the results on a differential elements located at…

Q: Find the maimum normal stress carried in the part shown. 0-Sin ar0.5in

Q: F V=FU M=hF Find the principal stress at point C and D

Q: Find the insitu stress

A: We will use the formula to find the resultant of two stresses on any oblique plane

Q: The bearing pad consists of a 150 mm by 150 mm block of aluminum that supports a compressive load of…

A: Given:A=150 mm x 150 mmP=6 KNθ=30°

Q: Find the shear stress in pin of DIA 0.25 in

A: Given: The diameter of pin, d = 0.25 in The load acting, P = 600 lb

Q: Find the principle stresses at A and maximum shear stress.

Q: of 3.0 mm is produced at the tom of the groove. Compute the maximum stress in the rod y axial…

Q: Find maximum shear stress

A: Given data : Normal stress in X direction= σX Normal stress in Y direction= σY Shear stress along XY…

Q: What is the Maximum Shear stress for Mohrs Circle?

Q: the stresses at point A.

A: To find Stresses at point A

Q: What is the magnitude of the having a radius of curvature o tensile stress of 140 MPa is ar 4.

A: 4. Given Normal stress = 140 MPa Crack length, a = 3.8 x 10-2 mm Radius of…

Q: Determine minimum principal stress

A: Given data : Normal stress in X direction (σX)=10 MPaNormal stress in Y direction (σY)=50 MPaShear…

Q: 5. Find the approximate shear stress

A: To find approximate shear stress developed Exact shear stress developed deformation of the spring

Q: C ):- Draw the MC stress elemen Find:-

A: given:σX=20ksiσy=14ksi

Q: a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly…

Q: cresses at A and B points according to the ven and show them on the stress element.

Q: center = MAX

A: Solution:

Q: No Normal stress acts on the neutral axis. Is it true or false? How?

A: When a beam is subjected to a bending moment the beam undergoes either hogging or sagging. In both…

Q: and (D). Calculate the stress he loads are applied, and ement of point (B). Use E =

A: given:

Q: 10 kN 4 kN/M 2.5 M 2.5 M 2.5 M 2.5 M B 1.0 M 2.5 M

A: The stresses in each cable of the given system can be calculated using the Lamy's theorem which…

Q: Determine the reaction loads and maximum shear stress ! 200 Ibf-in z-in dia. A B 4 in 6 in

Q: The R-ratio (minimum stress to

A: Given data; Determine the R ratio for this cyclic loading.During a high cycle fatigue test, a…

Q: Calculate the stress at a-a and b-b sections

A: FBD of AB & BC

Q: 5 - The ring supports the 1000-N load and is held in position by the two cables attached to vertical…

A: Given Load, P = 1000 N

Q: etermine the maximum shear stress in

Q: the normal stress at comer A.

Q: Find normal stresses and shear stress at the given inclination ..using mohr circle

Q: Determine the maximum tensile stress (MPa) at

A: Determine maximum tensile stress.

Q: 883KN V V V V V V V V ww.cos 3mm

A: given; weight density(w)=883KN/mlength of beam(l)=500mm =0.5mdiameter…

Q: a) Calculate the maximum stress in the steel ring. b) Calculate the pressure exerted by the copper…

A: we are to determine the stress generated in the composite ring

Q: find the stress in the balt. 3D emd Bearing at cdoat1mm 6 mm

A: Detailed Answer Given Below. kindly Check. 1.Stress in Bolt

Q: A gear made of aluminum (modulus of elasticity = 69,000 MPa) is press fitted onto an aluminum shaft.…

Q: at each of these he state of stress

Q: Find the maximum normal stress carried in the part shown.

Q: A shaft is required to fail when the torque on the shaft is 182 N-m. Find the suitable diameter of…

Q: Calculate normal and shear strains at the center

Q: find the piston diameter if the pressure 70000 N/m-and mass 2000g ? Select one: O a. 20mm O b. 314…

A: Here, Pressure P=70000 N/m2 Mass, m=2000g=2kg

Q: 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find…

A: The modulus of rigidity of the hollow steel shaft is, G=12×106 Psi The torque transmitted by the…

Q: For a force of 1.25 kN. compute the maximum stress at the fillet under the shoulder.

A: GIven: D=9 mm d=6 mm r=0.5 mm F=1.25 kN TO determine: Maximum stress at fillet

Q: Find the value of force which produce stress of 1.2 N/mm2 if cross sectional area is 0.5 mm2

A: Given data : Stress=σ Area=A Find : Force

Q: the maximum shear stress (in MPa) at the point is

A: Given; In a plane stress condition, Stress at a point are; σx=20 MPa σy=80 MPa σxy=40…

Q: 2. If 75 N/mm is the maximum shear stress and 50 kN-m is the torque acting on a solid shaft, then…

A: Given: Maximum shear stress τmax = 75 N/mm2 = 75000 kN/m2 Torque acting on a shaft T = 50kN-m…

Q: aft under the torsion has a pure shear stress on the surface. What is the maximum principal stress…

A: Given:A shaft under the torsion,stress on the shaft=τ

Q: When the stress conditions are given as shown below, calculate the vertical stress and shear stress…

A: Write the given information.

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

If the difference between tight and slack side for a leather belting doesnot exceed
100 N/cm of width for a belt 0.5 cm thick. Find the maximum stress in the belt.
Consider.
angle of lap = 170°
Belt speed
%3D
1000 m/min
%3D
density of leather = 10-3 kg/cm³
Coefficient of friction
0.25
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A generator driven by a wind turbine is required to deliver 5 MW of power at the generator terminals. The turbine is a two-blade propeller rotating about a horizontal axis and the maximum permitted shear stress of the turbine shaft is 55x106 N/m2 The rotor is designed to operate at a rotational speed of 45 revolution per seconds .The stage efficiencies are Cp 0.32, ngb = 0.90, ng = 0.92. %3D . (i) If the turbine delivers its rated power at a wind average speed of 22 m/s, calculate the corresponding diameter of the propeller and its TSR, assuming a typical value for the overall efficiency. The air density may be assumed to have a value 1.29 kg/m³. (ii) Calculate the torque on the turbine shaft.
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
A ship's shaft operates at 150 rpm and resists a maximum shear stress of 50 MPa. The shaft has an outer diameter of 45 cm and an inner diameter of 30 cm, as shown in the figure. Determine: What is the maximum power that can be transmitted without exceeding the allowable shear stress? If the rotational speed of the shaft is limited to half, but the same shaft power is maintained, what happens to the shear stress in the shaft?
A 14 cm x 18 cm air compressor has 6 bolts on cylinder head with yield stress of 450 MPa. If the bolt stress area is 0.14 in2, calculate the maximum pressure inside the cylinder.
A cylindrical tank with closed ends is filled with compressed air at a pressure of 500 kPa. The inner radius of the tank is 2 m and it has wall thickness of 10 mm. The magnitude of maximum in-plane shear stress (in MPa) is_______.
Q2. A mild steel shaft transmits ‘P’ kW at ‘N’ r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa. Power P in KW= 25 , Speed N in rpm=150
Calculate the combined stress (MPa) on the rod shown below using principle stress method.Here, F1 = 0.35 kN, F2 = 0.12 kN, T = 428000 N-mm. Length and diameter of the rod are 75cm and 75 mm, respectively.
A torque of T=2kNm and a torque of M=1kNm are applied to the thin-walled pressure tank as shown in the figure. Calculate the maximum internal pressure (p) that can be applied to the tank according to the von Mises distortion energy theory, with the radius of the tank r=50mm, the wall thickness t=3mm and the safety factor n=2.3. The yield strength of the tank material is Sut=380MPa.
Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 165o and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted.
A drill string is composed of 5,100 ft of 4½-in. drill pipe with a unit weight of 18 lbf/ft, 300 ft of 4½-in. heavyweight drill pipe with a unit weight of 41 lbf/ft of cross section 6.4023 in2, and 660 ft of 6¼-in. drill collars with a unit weight of 91 lbf/ft. If the drilling-fluid S.G 1,4 and assuming that the WOB is 34,000 lbf. Calculate the axial stress at the top of the hole and at the cross section located 2,000 ft from the top of the hole. Need Solution through 15min