find the mobility and determine the Grashof condition

Q: Find the tensions in the ropes that hold a 100N box. The ropes are considered weightless and are at…

A:

Q: Find the angle of tilt 6 with the horizontal so that the contact force at B will be one-half that at…

A: Given:

Q: Calculate the tension in each cable around the pulley.

A:

Q: A 3192kg car is going up the Amerat hill, at angle 16.8, with 2 people inside the car each of 49kg.…

A: Given, Mass of car =3192 kg Mass of passengers=2×49kg=98 kg Total Mass, m=3192kg+98kg=3290 kg Lift…

Q: Find the tension force in each 35 cabler 木 oss kg.

A:

Q: Find the reactions at the fixed connection at A. 4 N/m A 2m 4m

A:

Q: draw free body diagrams for each

A: Free body diagram A free-body diagram shows the forces acted upon the body. It is a special example…

Q: Calculate the magnitude of the force supported by the pin at A under the action of the 1.5-kN load…

A: Given data :  Load = 1.5KN = 1.5 x 103N Q = 30 Find :  Force at A = ?

Q: Determine the mobility and find the Grashof condition

A: Given data as per the question No. of links =4  No. of joints =4 No. of higher pair =0 we know…

Q: Calculate the effort (F) that has to be applied in the pulley system 100 kg

A:

Q: Find the angle of tilt θ with the horizontal so that the contact force at B will be equal to 0.26…

A: NB=.26NA angle of tilt θ FBD of smooth cylinder

Q: Find the maximum load P that can be supported by the tripod If the force in any legs is limited to…

A: Solution:

Q: n forces in the pin A and roller B,

A:

Q: Develop a free body diagram based on the structure. There must be a system FBD and an FBD of one…

A:

Q: calculate the forces on the rod by using the method of joint

A: The free body diagram of the truss is as follows:

Q: force Plt) acting on the Piston Causes Crankshaft AB to srotate • The mass per unit length of each…

A: Obliquity ratio,lr=N OE=r cos θBE=l cos βNsinβ=sinθ   x=OC-OBx=x+l-r cosθ+l cosβx=r1+lr-cosθ-l…

Q: Draw the FBD and derive the EOM of the pulley system below with respect to x using Ne

A:

Q: At what value of α would the tension in rope 2 be a minimum?

A: For the minimum value of tension in rope 2, the angle between the tensions must be 90 degrees.  Let…

Q: Please can you help with the free body diagram for this problem

A:

Q: In a hydraulic press, the small cylinder has a diamter of 1 in, while the large piston has a…

A: To Find : The force on the large piston. Given :  The diameter of larger piston is d=8 in. The…

Q: Solve the following system of equations for forces BC and

A:

Q: Calculate the tensile force in the cables AB and BC as shown to be frictionless. Presume the pulleys…

A:

Q: Determine the constraint equation that relates the bodies A and B.

A:

Q: Find the axial forces in the marked members (ef, ed and ec). loads are indicated in tonnes.

A: Above shown diagram is truss. For trusses we have two methods 1) Method of Joints. 2) Method of…

Q: if two forces of body, then their gnitude P and 2p act minimum resceltant ma on is

A: Given data: F1=PF2=2P Need to determine the minimum resultant force.

Q: The Diameters of a small piston and a large piston of a hydraulic jack are 5 cm ad 10 cm…

A:

Q: A uniform bar with mass M = 3.25 kilograms is shown in the diagram. hlo required to keep the

A:

Q: Calculate the reaction force at support B Calculate the reaction force at support B when the support…

A: Given: A propped cantilever beam as shown in Fig w= 7kN/m P= 14kN flexural rigidity (EI)= 4 MN.m2…

Q: Q3/Find the force required on the curve surface.

A:

Q: is applied at B where P = 19i - 10j kN.Note that the reaction force at A acts along the boom because…

A:

Q: The unstretched length of spring AB is 1 m. If the block is held in the eguilibrium position shown,…

A: Expression for length of AB;

Q: Find the angle of tilt 0 with t the contact force at B will be c the smooth cylinder.

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: 60 mm, 60 mm A R=75 mm 105 mm 100 N

A:

Q: Find the horizontal force , P required to turn the wheel weighing 500 over the block 10cm high if…

A:

Q: A man used a rod of length 5.00 m to lift a 700 kg marble. The fulcrum is 0.50 m from the end of the…

A: Given data  length of rod (L) = 5 m mass of marble (M) = 700 kg  fulcrum is at a distance from…

Q: Calculate the tension T in the cable which supports the 1000-lb load with the pulley arrangement…

A: ◆ The tension in the cable is 250 lb. ◆ The magnitude of the total force on the bearing of pulley C…

Q: etermine the torce in each cable needed fo support the flowerpot nose weight is 10ON

A:

Q: 2. Cable AB passes over the small ideal pulley C without a change in its tension. The length of…

A: Given data Weight of load W = 50N To determine the tension in the cable CD

Q: = the tension forces for

A: To find Tension forces

Q: . By Joints Method find the forces in each member.

A:

Q: Q/ Compute the pull force (F) on the rope exerted by the man to hold the crate in the position…

A:

Q: How much tension (Fm) must be supplied by the triceps to stabilize the arm against an external force…

A:

Q: 4. M= 2gL %3D Joo? B:

A:

Q: The homogeneous AB beam weighs 400 lbs. For each support condition in (a) a (d), plot the DCL of the…

A: (a) The DCL of the beam AB is given as, In this above diagram, two support reactions occur at the…

Q: A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If…

A: mass=3tonne=3metric tonConsidering that the distances are in mmVertical Distance =180+1080=1.26m…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.