This is a diagram of a domestic hot-water system. The gas valve is operated by the controller, which, in turn, is operated by the temperature measuring and comparing device. The gas valve operates the main burner in full-on/full-off modes. Hot Water Faucel (nomaly closed) Flue Gases Cold Water Pressure Reliel Valve Check Valve Temperature Measuring and Conoaring Device Controler Skop Valve Gas a) Draw a simplified Fault Tree for this hot-water system b) Find the minimal cut sets c) Find the minimal path sets

This is a diagram of a domestic hot-water system. The gas valve is operated by the controller, which, in turn, is operated by the temperature measuring and comparing device. The gas valve operates the main burner in full-on/full-off modes. Hot Water Faucel (nomaly closed) Flue Gases Cold Water Pressure Reliel Valve Check Valve Temperature Measuring and Conoaring Device Controler Skop Valve Gas a) Draw a simplified Fault Tree for this hot-water system b) Find the minimal cut sets c) Find the minimal path sets

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter11: Heat Transfer By Radiation

Section: Chapter Questions

Problem 11.14P

See similar textbooks

Similar questions

TOPIC: PRIOPERTIES OF SUBSTANCES:Note: The pressure values are absolute values unless specified.Determine the properties of H2O with units according to the following Table: Provide the complete solution
TOPIC: PRIOPERTIES OF SUBSTANCES:Note: The pressure values are absolute values unless specified.Determine the properties of H2O with units according to the following Table:
If you add heat of magnitude 800 kJ to a mass of 800g of water originally at a temperature 75 degrees C and the water eventually begins to boil. The latent heat of vaporization of water is 22.6 x 105 J/kg, and its specific heat capacity is 4186 J/kg · K. How much water is left in the container? How much heat does its take to get rid of all the water? How long would it take the water to boil away? Please do fast asap
Radiators are used in most of the houses’ heating. If we happen to place a sofa justin front of our heating radiator, how will the heating of the room be affected? Explain.
The factors that tend to increase detonation is SI engine led to reduce knocking in C1 engine. Dis this statement with reference to the following influencing factor 1. Compression ratio 2. Inlet temperature 3. Self-ignition temperature of fuel 4. Time lag of ignition temperature of fuel, and 5. Combustion chamber wall temperature
In the measurement with the thermoeleman circuit, whose voltage-temperature relation is linear and the calibration coefficient is 0.05 mV/ºC, it was understood that the temperature of the reference end is higher than 0ºC after the measurement point temperature is calculated as 80ºC. To resolve this error, this time the measuring tip was immersed in the water-ice mixture and a deviation of 0.15 mV was observed at the millivolt meter. How many ° C is the first value measured as 80 ° C? a. 76.25 b. 77.50 c. 78.00 d. 75.00 e. 77.00
Water melts as temp increases because : - chemical potential of the liquid is lower than that of gas - liquid and solid form eutectic mixture -chemical potential of the liquid and solid become equal
Choose the correct answer. Air temperature affects the rate of evaporation because: Temperatures provide heat required for evaporation Temperature controls latent heat of vaporisation Temperature influences the vapour pressure deficit.
In many temperature control applications, __________ is the controlled variable.
Most houses have vents that open and close manually without any central control.Cities across the United States advise the use of such vents in an effort to saveenergy. In most cases, household occupants do not use the entire house at the sametime; the tendency is to use certain rooms for long periods of time. For example,the family room and dining room may be used heavily, while the living room andkitchen are used at certain hours of the day. To cool or heat a room, the vent systemmust work to cool or heat the entire house. Energy saving can be enhanced if thevents of unused rooms are closed; this will push the hot/cold air to where it isneeded most and reduce the load of the conditioning system. Develop an objectivetree to clarify the need statement and prioritize the objectives laid out in the problem statement. You may add features that may not be listed clearly in the problemstatement but will give an additional advantage to the proposed design.
In the United States, energy for household heating is generally sold using English units, e.g., therm, gal, and cord. A house in Wisconsin uses 1200 therms of thermal energy during the heating season. Calculate the cost of fuel if the furnace uses (a) natural gas with an efficiency of 70%; (b) No. 2 fuel oil, efficiency 65%; (c) kerosene, efficiency 99.9% (unvented); and (d) wood with l5% moisture with an efficiency of 50%. Use the data in Tables 2.2, 2.7, and 2.13. The efficiencies are based on the HHV. Assume the cost of natural gas is $8/MBtu, the cost of No. 2 fuel oil is $3/gal, the cost of kerosene is $3.50/gal, and the cost of wood is $100/cord. Assume the bulk density of cord wood is 30 lbm/ft3 .
Q#01: Write down the functions of the following parts/accessories used with the equipment in heat and mass transfer laboratory. Compressor with thermal conductivity of building materials equipment. Up/down valve. DC power supply. Cooling section in linear module. Temperature selector in heat conduction study bench.