Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 40 mm x 43mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 10 kN(tensile), 25 kN (compressive), 22 kN (compressive) respectively. Take E as 120 GPa, Poisson's ratio as 0.3(figure - 0.5 mark, calculation - 1.5 marks, solution - 2 marks)(ENTER ONLY THEVALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET & UPLOAD YOUR HAND WRITTENANSWERS IN THE LINK PROVIDED)The stress along length direction (Unit in MN/m2)=The compressive stress along width direction (Unit in MN/m2?)=,The compressive stress along depth direction (Unit in MN/m?)=The change in volume of the block is (unit in mm)

Stress (σ) is defined the force per unit area.

Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 40 mm x 43 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 10 kN (tensile), 25 kN (compressive), 22 kN (compressive) respectively. Take E as 120 GPa, Poisson's ratio as 0.3 (figure - 0.5 mark, calculation 1.5 marks, solution - 2 marks) VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET & UPLOAD YOUR HAND WRITTEN (ENTER ONLY THE ANSWERS IN THE LINK PROVIDED) The stress along length direction (Unit in MN/m²)= The compressive stress along width direction (Unit in MN/m2)= The compressiye stress along depth direction (Unit in MN/m2) =

Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 40 mm x 43 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 10 kN (tensile), 25 kN (compressive), 22 kN (compressive) respectively. Take E as 120 GPa, Poisson's ratio as 0.3 (figure - 0.5 mark, calculation 1.5 marks, solution - 2 marks) VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET & UPLOAD YOUR HAND WRITTEN (ENTER ONLY THE ANSWERS IN THE LINK PROVIDED) The stress along length direction (Unit in MN/m²)= The compressive stress along width direction (Unit in MN/m2)= The compressiye stress along depth direction (Unit in MN/m2) =

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.9P: -9The stresses acting on element B in the web of a wide-flange beam are found to be 14,000 psi...

See similar textbooks

Similar questions

‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A circular cylindrical steel tank (see figure) contains a volatile fuel under pressure, A strain gage at point A records the longitudinal strain in the tank and transmits this information to a control room. The ultimate shear stress in the wall of the tank is 98 MPa, and a factor of safety of 2,8 is required. (a) At what value of the strain should the operators take action to reduce the pressure in the tank? (Data for the steel are modulus of elasticity E = 210 GPa and Poisson's ratio v = 0.30.) (b) What is the associated strain in the radial direction
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
The normal and shear stresses acting on element B are ??x= -46 MPa, sy= -13 MPa, and txy= 21 MPa (see figure for Problem 7.2-10). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
An aluminum pole for a street light weighs 4600 N and supports an arm that weighs 660 N (see figure). The center of gravity of the arm is 1.2 m from the axis of the pole, A wind force of 300 N also acts in the (y) direction at 9 m above the base. The outside diameter of the pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressive stresses o, and e1., respectively, in the pole (at its base) due to the weights and the wind force.
Two bars AC and BC of the same material support a vertical load P (see figure). The length L of the horizontal bar is fixed, but the angle fl can be varied by moving support A vertically and changing the length of bar AC to correspond with the new position of support A. The allowable stresses in the bars are the same in tension and compression. When the angle ft is reduced, bar AC becomes shorter, but the cross-sectional areas of both bars increase because the axial forces are larger. The opposite effects occur if the angle 0 is increased. Thus, the weight of the structure (which is proportional to the volume) depends upon the angle ft. Determine the angle ft so that the structure has minimum weight without exceeding the allowable stresses in the bars. Note: The weights of the bars are very small compared to the force P and may be disregarded.
Plastic bar of diameter d = 32 mm is compressed in a testing device by a Force P = 190 N that is applied as shown in the figure. (a) Determine the normal and shear stresses acting: on all faces of stress elements oriented at (1 ) an angle 8 = 00, (2) an angle ?? = 22.5s, and (3) an angle ?? = 45°. In each case, show the stresses on a sketch of a properly oriented element. What are smaxtmax (b) Find smax and tmax in the plastic bar if a re-cantering spring of stiffness k is inserted into the testing device, as shown in the figure. The spring stillness is 1/6 of the axial stiffness of the plastic bar.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.