Find the stresses in each direction, also find thechange in volume of the block of dimension 110mm x 55 mm x 40 mm, subjected to 3 mutuallyperpendicular loads. The load along length,breadth and depth directions are 14 kN(tensile), 20 kN (compressive), 10 kN(compressive) respectively. Take E as 160 GPa,Poisson's ratio as 0.3(ENTER ONLY THE VALUES IN THEBOXES BY REFERRING THE UNITGIVEN IN BRACKET & UPLOAD YOURHAND WRITTEN ANSWERS IN THELINK PROVIDED)The stress along length direction (Unit inMN/m?)=.The compressive stress along widthdirection (Unit in MN/m2)=.The compressive stress along depthdirection (Unit in MN/m2)=.The change in volume of the block is (unit inmm3) =.

stress is defined as the force per unit area.

Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 55 mm x 40 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 14 kN (tensile), 20 kN (compressive), 10 kN (compressive) respectively. Take E as 160 GPa, Poisson's ratio as 0.3

Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 55 mm x 40 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 14 kN (tensile), 20 kN (compressive), 10 kN (compressive) respectively. Take E as 160 GPa, Poisson's ratio as 0.3

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.11P: -11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0...

See similar textbooks

Similar questions

A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A circular cylindrical steel tank (see figure) contains a volatile fuel under pressure, A strain gage at point A records the longitudinal strain in the tank and transmits this information to a control room. The ultimate shear stress in the wall of the tank is 98 MPa, and a factor of safety of 2,8 is required. (a) At what value of the strain should the operators take action to reduce the pressure in the tank? (Data for the steel are modulus of elasticity E = 210 GPa and Poisson's ratio v = 0.30.) (b) What is the associated strain in the radial direction
-9The stresses acting on element B in the web of a wide-flange beam are found to be 14,000 psi compression in the horizontal direction and 2600 psi compression in the vertical direction. Also, shear stresses of magnitude 3800 psi act in the direct ions shown (see the figure for Problem 7.2-9). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
An aluminum pole for a street light weighs 4600 N and supports an arm that weighs 660 N (see figure). The center of gravity of the arm is 1.2 m from the axis of the pole, A wind force of 300 N also acts in the (y) direction at 9 m above the base. The outside diameter of the pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressive stresses o, and e1., respectively, in the pole (at its base) due to the weights and the wind force.
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A prismatic bar is subjected to an axial force that produces a tensile stress ????=65 MPa and a shear stress T??= 23 MPa on a certain inclined plane (see figure). Determine the stresses acting oil all laces of a stress element oriented at ?? = 30°, and show the stresses on a sketch of the element.
3-17 The stresses at a point along a beam supporting a sign (see figure) are sx= 2250 psi, sy,. = 1175 psi, and txy = -820 psi. (a) Find the principal stresses. Show them on a sketch of a properly oriented clement. (b) Find the maximum shear stresses and associated normal stresses. Show them on a sketch of a properly oriented element.
The normal and shear stresses acting on element B are ??x= -46 MPa, sy= -13 MPa, and txy= 21 MPa (see figure for Problem 7.2-10). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)