Find the stresss in the left rod after its lower end is attached to the support.
Q: 50* POINT A 200 POINT I
A:
Q: the state of stress at points A and B, and show the results on a differential elements located at…
A:
Q: etermine the normal stresses in bronze rods (1) and steel rod (2) after
A:
Q: Find the stresses at point C. -1.5 m 2.5 m 250 mm 125 mm 1.5 m 50 kN/m 50 mm 2 m 4m
A: Find the stresses at point C.
Q: The invariants of a stress system at any point are 1 = -2 MPa, I2 = -15 MPa and I3 = 0 MPa Find…
A: Given Data : Invariants of stress system are :σx=I1=-2 Mpaσy=I2=-15 Mpaζxy=I3=0 Mpa
Q: "ROBLEM .. Determine the magnitude and type of axial stress of the 1/8 inch wire and of the ¼ in.…
A:
Q: F V=FU M=hF Find the principal stress at point C and D
A:
Q: The figure shows the stresses at a point. Determine the principal stresses and the maximum shear…
A:
Q: 4. Mohrs Circle construction for generalized plane stress
A: Mohr's Circle of Generalized plane Stress.
Q: Q3) Show the state of stress at points A and B on the assembly at section 400 mm а-а. a 200 mm AB…
A: Write the given data: The load in the x-direction will produce twisting couple on the vertical…
Q: Find the principle stresses at A and maximum shear stress.
A:
Q: The bolt shown on the picture is subjected to total tensile force of 90 kN. Determine the tensile…
A:
Q: as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane…
A: Given: The diameter of the shaft, d = 20 mm = 0.02 m
Q: Find normal and shearing stresses at point A .
A: For the Normal Stress at pt.A (considering the maximum stress condition) Normal Stress, σx = PA…
Q: Find the missing stress components if T, = 70MP. , T, = 45 p., , %3D xy yz
A:
Q: the stresses at point A.
A: To find Stresses at point A
Q: What is the magnitude of the having a radius of curvature o tensile stress of 140 MPa is ar 4.
A: 4. Given Normal stress = 140 MPa Crack length, a = 3.8 x 10-2 mm Radius of…
Q: C ):- Draw the MC stress elemen Find:-
A: given:σX=20ksiσy=14ksi
Q: Find the minimum principal stress for the stress case given in the figure.
A:
Q: If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the…
A: As per given question If the allowable normal stress is 120MPa and the allowable shear stress is…
Q: Find the maximum normal stress carried in the part shown O-Sin 0.5in 3in 5000 I6 lin 2in So00 Ib 4in…
A: In this problem, the stresses are critical at two sections. First section is fillet section and…
Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…
A: Given Outside diameter, d2 = 0.8 in Inside diameter, d2 = 0.19 in…
Q: (a): The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of…
A: a) Given: The cylinder for a hydraulic press,*inside diameter d=300mm*outside radius…
Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…
A:
Q: QUESTION 4) For the given plane state stress, if the 14 MPa components at the inclined surface is…
A:
Q: - The state of plane stress is represented by the stress element below. Draw the Mohr's circle,…
A:
Q: The 4-In. diameter shaft shown above is made from a ductile brass alloy. Which of the following are…
A: Normal Stress = Force / Cross Section Area = 4*100 / (π 4^2) = 7.957747154 Ksi Shear force is to be…
Q: Quiz// For the state of stress shown in Figure below. Draw the Mohr's circle and find the principal…
A:
Q: The state of stress at a point in a component is ox = -14 ksi, oy = -20 ksi, Ty -4 ksi. Sketch the…
A:
Q: Show how to find the horizontal and vertical stresses (unknown a, and ay but known t) if u were…
A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…
Q: the normal stress at comer A.
A:
Q: Find normal stresses and shear stress at the given inclination ..using mohr circle
A:
Q: Take the micro-body from the self-loading member, and bear the stress on it as shown in Figure a.…
A: For the given stress element,…
Q: For the element shown find 1) Principle stresses and their direction 2) Shear stresses and their…
A:
Q: The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm.…
A:
Q: according to the given and show them on the stress element.
A:
Q: The solid rod shown in Fig. has a radius of 0.75 in. If it is subjected to the force of 800 lb,…
A: Given Data⇒ Diameter of the solid rod(d)=2R d=2×0.75 d=1.5 m Force applied (F)=800 lb…
Q: The solid rod shown in Fig. has a radius of 0.75 in. If it is subjected to the force of 800 lb,…
A: Given Data The radius of a solid rod, r=0.75 in load, P=800 lb
Q: Fill in the blanks . Draw and label the Mohr’s circle. For sigma-yp = 15 ksf, does this fail? Find…
A:
Q: Find the principal stress at point C and D
A: The force F causes the bending moment at point C, and at point D only shear force will be there…
Q: na stressed element, the value of normal stress along 'X' and 'Y' directions are 200 MPa (tensile)…
A:
Q: Find the maximum normal stress carried in the part shown.
A:
Q: . The solid rod shown below has a diameter of 25 mm. Calculate the stresses that act at points A and…
A: For the given loading diagrams, Calculate the moment of inertia, Z=π64d4Z=π64254Z=19174.76 mm4…
Q: The solid rod shown in Fig. has a radius of 0.75 in. If it is subjected to the force of 800 lb,…
A: Given: Diameter of the rod (D)=1.5inForce (F)=800lb
Q: the figure showin, what skould be the minimum diameter of own if the allowable axial stress is Go…
A: given:σmax=60mpaτmax=110mpa
Q: In the figure, the nut is tightened by applying 450 N to a lug wrench. Show the stresses on the…
A:
Q: Determine the equivalent state of stress on an element at the point which represents (a) the…
A: steps of creating a mohr's circle are:- locate the points on graph considering horizontal axis for…
Q: aft under the torsion has a pure shear stress on the surface. What is the maximum principal stress…
A: Given:A shaft under the torsion,stress on the shaft=τ
Find the stresss in the left rod after its lower end is attached to the support.
Step by step
Solved in 2 steps with 2 images
- A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.AW310 × 74 wide-flange steel column with length L = 3.8 m is fixed at the base and free at the top (see figure). The load P acting on the column is intended to be centrally applied, but because of unavoidable discrepancies in construction, an eccentricity ratio of 0.25 is specified. Also, the following data are supplied: E = 200 GPa, y = 290 MPa, and P = 310 kN. What is the maximum compressive stress max in the column? What is the factor of safety n with respect to yielding of the steel?
- A large spherical tank (see figure) contains gas at a pressure of 420 psi. The tank is 45 ft in diameter and is constructed of high-strength steel having a yield stress in tension of 80 ksi. (a) Determine the required thickness (to the nearest 1/4 inch) of the wall of the tank if a factor of safety of 3,5 with respect to yielding is required. (b) If the tank wall thickness is 2.25 in., what is the maximum permissible internal pressure?A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?A scuba t a n k (see fig ure) i s bci ng d e signed fo r an internal pressure of 2640 psi with a factor of safety of 2,0 with respect to yielding. The yield stress of the steel is 65,000 psi in tension and 32,000 psi in shear, (a) If the diameter of the tank is 7,0 in., what is the minimum required wall thickness? (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure?
- A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?-7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the weight density of steel.
- A threaded steel rod (E=210 GPa, dr = 15mm, linear coefficient of expansion=12x10-6/0C) is held stress-free between rigid walls by a nut and washer (dw = 22mm)assembly at each end. If the allowable bearing stress between the washer and the wallis 55 MPa and the allowable normal stress in the rod is 90MPa, determine themaximum permissible temperature drop.Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?circular cross-section belt pulley system supported by two bearings tensioning forces formed in belts in Shaft power transmission T11 = 8 kN, T12 = 2 kN, T21 = 8 kN and T22 = 2 kN. Pulley weights are 1 no.lu pulley for both pulleys W =6 kN. Each two pulley diameters d = 1,2 m dir. a = 0.2 m ve b = c = 0,4 m. Slip safety stress Jul = 70 MPa a-) Greatest shear stress (TRESCA) b-) The diameter of the shaft (d) according to the largest change in shape (VON MISES) criteriayou can find.