please give clear answer, they are all related.thanks. Find the total magnitude of force, EFy acting in y-direction (answer in newton, N with a singledecimal place)Answer:Find the magnitude of the resultant force, FR acting on the bracket (answer in newton, N with asingle decimal place)Answer:Find the angle of the resultant force, FR measured counterclockwise from the positive x' axis(answer in degree, ° with a single decimal place) A bracket mount is pulled by three forces as shown in figure below. Given: F1=293 N, and 0=25°yA F2 = 200 NF3 = 180 N1360°F,12Find the total magnitude of force, EFx acting in x-direction (answer in newton, N with a singldecimal place)

In the given problem, following formulae for determining the resultant will be used Magnitude of the…

Answered: Find the total magnitude of force, EFy…

Engineering

Mechanical Engineering

Find the total magnitude of force, EFy acting in y-direction (answer in newton, N with a single decimal place)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.21P: Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10...

See similar textbooks

Similar questions

A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo is unloaded by a container handling crane. Each bollard is fastened to the wharf using anchor bolts. Three cables having known tension force magnitudes F, = ll0 kN.F, = 85kN.and F, 9OkNare secured to one bollard at a point A with coordinates (0.0.45 m. 0) in the x-r-: coordinate system shown in the figure part b. Each cable force is directed at an attachment point on the ship. Force F, is directed from point A to a point on the ship having coordinates (3 m, 9 m. 0) force F, is directed at a point with coordinates (6.5 m. 8.5 m. 2 m) and force F, is directed at a point with coordinates (8 m. 9 m. S m). The diameter of each anchor bolts is 4 24 mm. (a) Find the reaction forces and reaction moments at the base of the bollard. (b) Calculate the average shear stress in the anchor bolts (in the x-: plane). Assume each bolt cart ics an equal share of the total force.
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
If the R-value of a construction material is 2.0, what isits U-value? A. 0.25 B. 0 50 C. 1.0 D. 2.0
.15 A hitch-mounted bicycle rack is designed to carry up to four 30-lb bikes mounted on and strapped to two arms Gil (sec bike loads in the figure part a) The rack is attached to the vehicle at A and is assumed to be like a cant silkier beam A BCDGII (figure part b) The light of fixed segment AB is U = 10 lb. centered 9 in. from A (see figure part b) and the rest of the rack highs W2 = 40 lb. centered 19 in. from A. Segment ABCDG is a steel tube o(2 X 2 in. with a thickness I = 118 in. Segment BCDGII pivots about a bolt at B with a diameter d1 = 0.25 in. to allow access to the rear of the vehicle without removing the hitch rack. When in use, the rack is secured in an upright posit ion by a pin C(diameter o( pin d, = 5116 in.) (see phoo and figure part C). The of returning effect of the bikes on the rack is resisted by a force couple F h at BC. (a) Find the support reactions at A for the fully loaded rack. (b) Find forces in the bolt at B and the pin at C. (c) Find average shear stresses in both the bolt at Band the pin at C. (d) Find average bearing stresses o, in the bolt at B and the pin at C.
In the figure below, all the bearings are movable bearings and the C bearing is in an inclined position. Draw the M, N, T diagrams according to your force values. (20kN force is perpendicular to the beam it acts on. P1, P2, P3 forces are in the vertical direction.) q=7 kN/m P1=25 kN P2=27 kN P3=11 kN
Consider the following coplanar system of tensile forces: F1 = 90 N at 180°, F2 = 150 N at 310° and Fy = 400 N at 0°. Use the counter clockwise direction as the positive direction of the angle from the positive x-axis. Provide the answers to 2 decimal places.
A load weighing P kN aswith AB, AC and AD cables such asare carried. Points A and B are x-axis, Cand D points are on the y-z plane.Specific to your name in the data tableAB, AC and AD cable using ratingsCalculate the forces. P (kn) = 440 L1 (m) = 11 L2 (m) = 10 L3 (m) = 16 L4 (m) = 18 L5 (m) = 16 L6 (m) = 5
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
A 40 kg-mass hangs from the end of a uniform beam. The beam is 6.0 m long and has a mass of 60 kg. The beam is supported at the left end by a hinge at the wall and by a cable at the right end. The other end of the cable is tied to the wall at a point 4.0 m above the left end of the beam. (g = 9.81 m/s² )A. Draw the FBD;B. Find the tension (T) in the supporting cable in Newtons; andC. Find the reaction force (R) of the hinge on the beam ( magnitude and direction).
As shown, an L-shaped bar is supported by a pin at joint A. The bar's dimensions are aaa = 620 mmmm and bbb = 400 mmmm , and the bar is subjected to a force with magnitude FFF = 5.05 kNkN at joint B. Ignoring the bar's weight, find the actual orientation of the applied force. What is the value of the angle θθtheta?
Under non-uniform and slippery road conditions, two forces (u and w), shown in the figure (image 1), are performed on the truck's rear wheels, which have a limited slip rear differential. Choose the alternatives that are true: (data: u = 92lbf and w =57lbf) (obs1.0: 1''= 1 in = 25,4mm) (obs2.0: 1lbf = 4,448N) a) the force vector resulting from the two forces is -149i [lbf] b) the resultant of the two forces has an intensity equal to 149lbf c) the ordinate of the point of intersection of the line of action of the resultant of this system of forces with the y axis is 7.05in d) adopting the counterclockwise direction as positive, the total moment of the two forces in relation to point g is equal to -1050lbf.in e) the total moment vector in relation to the G point is equal to -1050i [lbf.in]
The crate weighing 100kg is balanced as shown in the figure. Find the tensile strength on each wire to maintain this state. (Considering Cartesian coordinates). I have been trying so long for this question and I couldn't solve it . Please help me.