Find the work done in pumping gasoline that weighs 42 pounds per cubic foot. The top of a cylindrical gasoline storage tank at a service station is 4 feet below ground level. The axis of the tank is horizontal and its diameter and length are 7 feet and 15 feet, respectively. Find the work done (in ft-lb) in pumping the entire contents of the full tank to a height of 3 feet above ground level. (Round your answer to tw

Q: What is the ratio of total convective heat transfer rate to laminar convective heat transfer rate…

A: Given that,Kinematic viscosity, Length of plate, L=2mVelocity, V=10m/sWe have to find the ratio of…

Q: Determine the moments of inertia about the centroidal x-axes of the trapezoidal area. a=147 mm;…

A: The dimensions of the trapezoidal area,a = 147 mm, b = 294 mm, h = 441 mm

Q: iv. G(s) = 54 s²+12s+36 a) Find the location of the poles, natural frequency and damping ratio…

A: a) Poles: s=-6 (repeated pole) Natural Frequency: ω_n = 6 Damping ratio: ζ = 0.5b) Step response =…

Q: HELP ME WITH THIS THERMODYNAMIC PROBLEM Subcooled water at the pressure of 10 MPa and temperature…

A: determine the work and heat transfer in the process

Q: Calculate the output speed and direction of gear 4. N₁ = 8 teeth n₁ = 1800 RPM CW N₂ = 24 teeth N3 =…

A: The speed of gear 1, The number of teeth on gear 1, The number of teeth on gear 2, The number of…

Q: (d) (Develop a model, in final integrated form, to estimate the concentration of species A exiting…

A: The wastewater that enters the tube and contains 10 g/m3 of benzene (solute A) dissolved in water is…

Q: Problem 1 A hot water pipe is used for domestic applications is insulated with a layer of calcium…

A:

Q: What percentage of initial energy is lost in this jump?

A: Given dataF1 = 10The percent of initial energy lost is the ratio of E2/E1

Q: Draw shear force (V-x) and bending moment diagrams (M-x) for beams and loads in Figure 3.

A:

Q: Movement of 80 kg crate What is the minimum force that must be sufficient for the ballot box? should…

A:

Q: (2) The correct calculation for determine the displacement at Point C of the following beam by using…

A: As per graph multiplication method of displacement at a point, displacement is given by…

Q: Draw a complete, clearly labeled, FBD of member AD.

A: Given data is

Q: Consider the mechanism of Bar AB, Bar BC, and roller A. Roller A is constrained to move along the…

A: Consider the mechanism of Bar AB, Bar BC, and roller A. Roller A is constrained to move along the…

Q: 6/185 The body composed of slender rods of mass p per unit length is lying motionless on the smooth…

A:

Q: Using the following lines, let us create a virtual data concerning the joint torque (Nm) and angular…

A: Given:To find:Torque average

Q: 400 mm Fr= 800 N 150mm -Ft= 600 N Fa = 4,00 L 450mm Draw bending torsional moments, shear forces and…

A: The force acting at gear C in negative y-direction , Fr = 800 NThe force acting at gear C in…

Q: Answer: Wmax = kN/m B

A: According to the given dataL=1.7md=18mmWe need to find the uniform distributed load w

Q: Q3/ Find the area of the region enclosed by the parabola y² = 8x and the line y=2x.

A:

Q: On its takeoff roll, the airplane starts from rest and accelerates according to a = ao - kv² where…

A:

Q: (gpt/Ai wrong answer not allowed) In a body-and-tube heat exchanger with two shell passes and 12…

A:

Q: For the system given in the figure on the right-hand side, where the input is four-unit step i.e., r…

A: givenAs per the Bartleby policy I am solving Part a, b, c and d.

Q: Q/ Using the moment distribution method, find support reactions of the frame shown; assume EI =…

A: Given:The length of AB is .The length of BC is .The length of BD is .Procedure of calculating…

Q: A nylon-core flat belt has an elastomeric envelope, is 250 mm wide and transmits 50 kW at a belt…

A:

Q: How did they get the Fab and Fbc?

A: Given DataFindThe unknown forces FAB and FBC

Q: A cable that weighs 6 lb/ft is used to lift 500 lb of coal up a mine shaft 350 ft deep. Find the…

A: Mass of cable per unit length, m = 6 lb/ftMass of coal, Mc = 500 lbDepth, h = 350 ftRequired:W (…

Q: A rocket runs out of fuel in the position shown and continues in unpowered flight above the…

A: Given data as per question

Q: Two forces are applied to an AISI 1050 HR post BD, as indicated. Knowing that the cross section of…

A: Cross-section of the vertical part, A = 1.5 in x 2.4 inThe yield strength for AISI 1014 HR steel, Sy…

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500-lb load.…

A:

Q: Compare the strain energies of two bars of the same material and length and carrying the same…

A:

Q: The turnbuckle is tightened until the tension in cable AB, is T-3.2 kN. Calculate the magnitude of…

A: Tension in the cable AB is 3.2 kN Find the moment about the line OP

Q: Arm AB has a constant angular velocity of 16 rad/s counterclockwise. At the instant when 0 = 0,…

A: Arm AB has a constant angular velocity of 16 rad/s counterclockwise. At the instant when, thita =…

Q: The equivalent stress for welding in given bracket connections would be if t te = 5mm i.e. Effective…

A: Effective throat thickness of weld te = 5mmP = 50 × 10³ KNe = 200 mmh = 250 mm

Q: 60 mm 54 mm 120 mm 40 mm r- 16 mm 27 mani 18 mm 5. Machine Element For the machine element shown,…

A: According to the given dataThere is a composite structure of the 4 segmentWe need to findCenter…

Q: 29) For the shaft and hole sizes shown in the figure, specify the type of f 5.000 4.997 11 Clearance…

A: This question is based on the concept of limit fit and tolerance.As per the guidelines we are…

Q: In a food processing plant, hot liquid water is being transported in a pipe (k = 15 W/m .K, D₁ = 2.5…

A: kpipe = 15 W/m.kDi = 2.5cm=0.025mDo= 3cm = 0.03mL = 10 mTi = 100oCTe = 60oCTe 45oCThe properties of…

Q: I took a flight from Los Angeles to Denver, and I carried with me a closed water bottle of the type…

A:

Q: 04: 3 kg of air at 1.5 bar pressure and 77°C temperature at sta PUO polytropically to state 2 at…

A:

Q: t₁ = t2 = i i sec, |v|= Mi sec, |v|= i ft/sec ft/sec

A:

Q: Q1: Air expands from a storage tank through a converging diverging nozzle having a hroat area of (70…

A: Given:The throat area is .The shock area is .The exit area is .The pressure and temperature is  and…

Q: In the continuous and incompressible flow of water with a temperature of 20°C and a density of 998…

A:

Q: Using the method oj joints, determine the force in each member of the truss

A:

Q: Problem 1. For the truss carrying a vertical load P as shown in Figure 1 have constant AE, determine…

A:

Q: 8 KN 2m 10 kN- 2m -1.5m- oc B

A:

Q: The bar AB of 3.62kg is attached to the collar A of negligible mass and a wheel of mass 15.81kg with…

A: Mass of bar AB = 3.62kgMass of wheel = 15.81kg Turning radius = 0.16 mAngular velocity of the wheel…

Q: Given a distributed load, how do we find the location of the equivalent concentrated force?

A: Given a distributed loadfind out:how do we find the location of the equivalent concentrated force

Q: The system is at rest with the spring unstretched when = 0. The 5.3-kg uniform slender bar is then…

A: We begin by calculating the change in the kinetic and the potential energy of the system. The change…

Q: 02 Q Similarly, there is oxygen gas (02) in the piston-cylinder assembly at a volume of 0.4m^3…

A: Initial condition -Final Condition-T2 = 97o C= 370 K

Q: The beam shown supports a load that varies uniformly from 100 N/m at the left end to 200 N/m at the…

A:

Q: End B of slender rod AB hits block C and causes the latter to move by a distance of 300 mm before…

A: mass of rod is m=1.5kgmass of block C is mc=0.5kglength of the block C is L=300mmcoefficient of…

Q: if the surface and the adjoinig air temperatures of a surface are same as 20 degree C and the…

A: T = 20 Ch=20 W/m²KRH= 40%

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.