I need the answer as soon as possible Given the partially completed state diagram of a Mealy sequence recognizer below, answerthe following questions:0/01/01/00/01/00/0ABE0/00/11/01/0ResetQI) What is the minimum number of flip flops required to design the sequence recognizor?Q2) What is the sequence that generates output 1' when detected? Assume the bits in theanswers are entered to the sequence recognizer from left to right.Q3) Given that sequence overlapping is allowed, what is the next state if the current state is"C and the input is 1?

1. Total number of flip flop required = ceil(log # of States) = ceil(log 5) = 3

following questions: 0/0 1/0 1/0 0/0 1/0 A C D E 0/0 0/1 1/0 1/0 Reset Q1) What is the minimum number of flip flops required to design the sequence recognizur? Q2) What is the sequence that generates output "1' when detected? Assume the bits in the answers are entered to the sequence recognizer from left to right. Q3) Given that sequence overlapping is allowed, what is the next state if the current ctato in B

following questions: 0/0 1/0 1/0 0/0 1/0 A C D E 0/0 0/1 1/0 1/0 Reset Q1) What is the minimum number of flip flops required to design the sequence recognizur? Q2) What is the sequence that generates output "1' when detected? Assume the bits in the answers are entered to the sequence recognizer from left to right. Q3) Given that sequence overlapping is allowed, what is the next state if the current ctato in B

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

A Gray code is a sequence of binary numbers with the property that no more than 1 bit changes in going from one element of the sequence to another. For example, here is a 3-bit binary Gray code: 000, 001, 011, 010, 110, 111, 101, and 100. Using three D flip-flops and a PLA, construct a 3-bit Gray code counter that has two inputs: reset, which sets the counter to 000, and inc, which makes the counter go to the next value in the sequence. Note that the code is cyclic, so that the value after 100 in the sequence is 000.
Design a Moore FSM for a Sequence Derector that detects five consecutive bits of "zero" in the input stream of bits, labeled x. The output z equals 1 if, during five consecutive clock cycles, the input x was equal to "zero". Once the sequence is detected, the FSM returns to the initial state S0. Add an asynchronous reset, active low, to the FSM.
Design a state machine to output the binary values (include leading zeros e.g. 0101} for the following sequence each time a increase count input line changes from 0 to 1. When it reaches the end it starts over at beginning {1, 3, 9, 5, 7, 3}. It has a second input line forward/reverse which will change its direction to go in reverse direction if this line is high..
Using the convolutional code and Viterbi algorithm described in this chapter, assuming that the encoder and decoder always start in State 0, determine the following:1. a) The output string generated for the input: 10010110.2. b) In which state is the encoder after the sequence in Part a is read?3. c) Which bit is in error in the string, 11 01 10 11 11 11 10? What is the probable value of the string?
If the floating-point number representation on a certain system has a sign bit, a 3-bitexponent and a 4-bit significand: • What is the largest positive and the smallest positive number that can be stored on this?system if the storage is normalized? (Assume no bits are implied, there is no biasing,exponents use two's complement notation, and exponents of all zeros and all ones areallowed.)• What bias should be used in the exponent if we prefer all exponents to be non-negative?Why would you choose this bias? show work and write out solution
A 4-bit prime number detector is a CLN whose output is 1 if the input, interpreted as 4-bitunsigned binary number, is a prime number (2, 3, 5, 7, 11, 13). a. Draw the truth table for this CLN. b. Construct a logic equation directly from your truth table by identifying mintermswhose output is ‘1’. Minimize it as much as possible using the theorems of Boolean algebra or KMAPS. c. Draw a schematic from your minimized logic equation.
Starting from an initial value of R in Hex is A4 determine the sequence of binary values in R after a logical shift-left, followed by a circular shift-right, followed by a logical shift-right and a circular shift-left. explain through the proper diagrams.
Given the Boolean function F below, reduce it to a simplest form using identity laws. Provide step-by-step activities along with the identity used at each step. F(X,Y,Z)= X’Y’Z + X’YZ + XY’Z + XYZ
A circuit has four inputs p,q,r,s representing the natural binary number 0000=0,to 1111=15 p is the most significant bit .the circuit has one output, x,which is true if the input to the circuit represent is a prime number and false other wise (A) design a true table for this circuit, and hence obtain an expression for x in terms of P,Q,R,S.
A Sequence Detector is a circuit which given an input string of bits generates an output 1 whenever the target sequence (pattern) has been detected. There are two types of sequence detectors: Overlapping: The detector allows overlapping, hence the final bits of one sequence can be the start of another sequence. Non-overlapping: The detector does not allow overlapping, hence a new sequence starts only after the previous sequence is completed. Ex: Detect pattern 101 For non-overlapping case: Input :0110101011001 Output:0000100010000 For overlapping case: Input :0110101011001 Output:0000101010000 Design a sequential circuit (overlapping) with an input ‘x’. The pattern to be detected is the binary number that is equal to 1001100 For example,the circuit detects the sequence 00010 . When the sequence is detected, the detector outputs z=‘1’ For this circuit: Draw the ASM diagram. Construct the state table. Draw the logic circuit for the datapath and control in logisim.
If the floating-point number representation on a certain system has a sign bit, a 3-bit exponent and a 4-bit significand: What is the largest positive and the smallest positive number that can be stored on this system if the storage is normalized? (Assume no bits are implied, there is no biasing, exponents use two's complement notation, and exponents of all zeros and all ones are allowed.) What bias should be used in the exponent if we prefer all exponents to be non-negative? Why would you choose this bias?
Design a sequence detector that searches for a series of binary inputs to satisfy the pattern 1011 (left to right – one-zero-one-one). The output (Z) should become true every time the sequence is found, including overlapping patterns. Draw two State Diagrams (one for Mealy and one for Moore).