The question is in the picture. Thanks Problem 1 of 2:ratio v= 0.3, that has elongated by 12 mm, what is its new radius iforiginally it had a radius of 50 mm ?For a 10-meter rod made of the material with Poisson'sIN(a) 50.018 mmL-(b) 49.982 mm(c) 50.400 mm(d) 49.600 mmPL'-(c) 0.77

Elongation ∆l=12 mm Length l=10 m = 10000 mm Poisson's Ratio ν=0.3 Initial Radius= 50 mm Initial…

Answered: For a 10-meter rod made of the material…

For a 10-meter rod made of the material with Poisson's ratio v= 0.3, that has elongated by 12 mm, what is its new radius if originally it had a radius of 50 mm ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. A circular opening 4 ft. in diameter is closed by a hemispherical shell weighing 2,800 lb. A.…

A: Given: Diameter of circular opening = 4 ft Weight of hemispherical shell = 2800 lb

Q: A spar buoy is a rod weighted to float vertically, as shown in the image. Let the buoy be maple wood…

Q: The shape of a piece of unknown material is intricate. It weighs a total of 185 g. When you submerge…

Q: A plate of size 60 cm x 60 cm slides over a plane inclined to the horizontal at an angle of 30°. It…

A: We will apply force balance

Q: 3) Two hemispherical shells are bolted together as shown in the figure. The resulting spherical…

Q: Determine the total change in length of the 25-mm-diameter rod when it is acted on by three forces…

Q: For a 10 m of rod made of the material with Poisson's ratio v=0.3, that has elongated by 12 mM, what…

A: length of rod= 10m elongation in rod = 10mm radius = 50mm

Q: QUESTION # 2 A brass cube 6 in on a side weighs 67 Ib. We want to hold this cube in equilibrium…

Q: A lead cube has a total mass lead-113. of 80 kg. What Is the length of its side? Sp, gr. of

Q: A bin holds a cylinder as shown. Each cylinder weighs 800 kN and has a diameter of 600 mm. The width…

A: The FBD of the section is shown below:

Q: You have a table as seen below. You'want to sit close to one edge, but when you sit, the other side…

A: Here,W = 4.4 mW1 = 1.2 mW2 = 1.6 mh = 1.1 mg = 9.81 m/s2Weight of table (N) = 32.7 kgWeight of…

Q: The thin plate shown in the figure below has densityp and thickness t. Calculate product of inertia…

A: let horizontal direction is Z and vertical is Ydevide this section in two area for area 1…

Q: A sphere 1.5m in diameter floats half submerged in tank of oil (SG=0.80). What is the total weight…

Q: A transmission tower shown below is subjected to lateral loads as shown. A =2.3 kN, B =5.7 kN, C…

A: Given, Lateral loads , A=2.3 kN B=5.7 kN C= 6.8 kN

Q: Q2: How to measuring the density by hydrometer and pycnometer?

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: or the machine elem gravity.

A: Given:- machine element To find:- y cordinate of the center of gravity

Q: Figure shows a metal part hanging by a thin cord from a floating wood block. The wood block has a…

Q: QUESTION 6 A beam with the cross-section shown is carrying a bending moment of M. Calculate the…

A: Bending Stress- Bending Moment when generated due to loading or directly moment applied it makes the…

Q: 2. A lead cube has a total mass of 200 kg. What is the length of its side? Sp. gr. of lead = 11.3

Q: Q3/ For the figure shown below, compute .the centroid of the figure 6m 3m 4.5 m Please, I want to…

A: Given:- To find:- Location of centroid

Q: 4. If a block weighs 3000 lb, solve for the gravitational potential energy that has been made after…

A: Energy is a significant property that is used to transform to a body or a system to execute work on…

Q: A door in a tank is in the form of a quadrant of a cylinder of 2 m radius and 2 m wide as shown in…

A: step 1-

Q: If the deformation of a spring is 0.9 m and the unstretched length 1.2 m, what would the stretched…

Q: For the configuration shown In the figure below what must be the value of the specific weight of the…

Q: QUESTION #1 A cube 80 mm on a side is made of a rigid foam material and floats in water with 60 mm…

Q: A structural member with a rectangular cross-section as shown in the accompanying figure is used to…

A: The given data is: P=2500 N l=20 cm A=0.1*0.005 m FS=2

Q: If the friction force on the 6 kg object is 10 N. Find the coefficient of friction force ?

Q: The shape of a piece of unknown material is intricate. It weighs a total of 2 kg. When you submerge…

Q: Which length shall I use to calculate current density: the whole bar length or the embedded length…

A: Answer embedded length is known as the length of the embedded steel reinforcement, The embedded…

Q: A dam for a reservoir is 30 meters high. A rectangular gate at the bottom of the dam is to be lifted…

A: Given: The height of the dam is 30 m. The dimension of the gate is 2 m x 1 m.

Q: A solid brass sphere of volume 0.305 m3 is dropped in an ocean, where water pressure is 2 x 107 N/m2…

Q: A copper wire is 1.0 m long and its diameter is 10 mm. If the wire hangs vertically, how much weight…

Q: 1. A 100-lb force is pulling a 200-lb block as shown. The coefficient of static friction between the…

Q: 1.) A barometer reads 760 attached to a tank is a pre that reads 950 cm of oil (s What is the…

A: Given that Barometer Reade 760 mm of Hg = Patm Patm = atmospheric pressure Gauge pressure = 950 cm…

Q: If aluminum weighs 25.9 kN/m3, how much will a 305-mm-diameter sphere weigh when immersed in water?…

A: Introduction : Unit Weight : Unit weight =Weight Volume units: Weight : KN Volume : m3 Given that…

Q: Question 2: 150 mm 150 mm 150 mm 100 mm A 2-mm thick piece of sheet steel is cut and bent into the…

A: Given data:- Density of steel, ρ=7850 kg/m3

Q: A steel tape of nominal length 200 m with a plumb bob of mass 16 kg attached to it was used to…

Q: Determine the effective area of the figure as shown.

A: Since their are no holes provide in connected member. Gross area is equal to Effective area.…

Q: The block weighing 1 kN is subjected to the forces as shown. Assuming the block starts at rest,…

A: Force in the vertical directionmg = 800Sin30 + 1000×35⇒mg = 1000⇒m = 101.937 Kg

Q: Q3. A copper bar of 50 mm*50 mm cross section is 1.5 m long, it subjected to an axial pull of 100…

Q: A figure shows a differential manometer connected at 2 points A and B. At A pressure is 100 kn/m^2.…

Q: A sphere 1.5m in diameter floats half submerged in tank of oil (SG=0.80). What is the total weight…

A: Buoyancy force isFB=1243π0.753 γoilWeight of sphere isWS= 43π0.753 γS

Q: 1. A wire of I mm diameter and I m long fixed at one end is stretched by 0.01 mm when a load of 10…

A: Youngs modulus of elasticity = 1.25x1013 N/m2

Q: a board is 8 m long. How high will one end be raised so that a block on it will just begin to slide…

Q: A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’s volume is…

A: Given data, Pressure P2 = 4666 psi Volume V1 = 805.407 in3 Bulk modulus K = 305000 psi

Q: 1. A wire of I mm diameter and 1 m long fixed at one end is stretched by 0.01 mm when a load of 10…

A: Given:- Diameter of wire = 1mm = 10-3m Change in length of wire= 0.01mm= 10-5 m Load on wire= 10kg…

Q: A 600 N ball is thrown downward with an initial velocity of 3 m/s from a height of 1.5 m above a…

Q: If the pressure at the bottom of an open tank is 593 kPa, find the unit weight (kN/m2) of gold in…

A: In the question, it is mentioned as gold whereas in figure it is mentioned as titanium. Whether it…

Q: ) The hemispherical dome in the figure weighs 30 kN and is filled with water and attached to the…

A: Solution: Consider the figure of the hemispherical dome:

Question

The question is in the picture. Thanks

Problem 1 of 2:
ratio v= 0.3, that has elongated by 12 mm, what is its new radius if
originally it had a radius of 50 mm ?
For a 10-meter rod made of the material with Poisson's
IN
(a) 50.018 mm
L-
(b) 49.982 mm
(c) 50.400 mm
(d) 49.600 mm
P
L'-
(c) 0.77

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data and Formula

VIEW

Step 2 Calculations

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Lateral earth pressure distribution against retaining walls

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cross section of a quarter circular concrete block JKL as shown in Figure 5 is located at thebottom of a reservoir. The width (perpendicular to the paper) is 3 m. The specific weight of theconcrete block is 24 kN/m3. The coefficient of friction between the base of the block and thefoundation is 0.43. Determine if the concrete block is stable or not against sliding and overturningif the water is:A. At side XB. At side Y, with the same water level as A.
Answer only A and B. note: a = 4.5 m b = 33.0 kN/m c = 13 kN
3 - What is the maximum permissible value (length x depth) for Applet on a rail vehicle wheel? A) 5 x 1.5 mmB) 4 x 0.5mmC) 7 x 1.5 mmD) 6 x 0.5 mmE) 6 x 1 mm
A 50m tape weighing 0.03kg/m is used to measure distance AB. The tape is supported at both end points and at its midspan and then applied tension is 6kg. Determine the total sag correction if the measured distance is 1,320.50m.
determine the relative error of the closure
4. An aerial copper wire (E =1x 10 5 N/mm ^2) 40 m long has cross sectional area of80 mm2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculatethe maximum weight which this wire can support at its lower end if the limiting valueof stress is 65 N/mm 2.a. 4627 Nb. 4281 NC. 4519 Nd. 5188 N
A 40m steel tape is suspended in the air between a theodolite and vertical rod, which is placed exactly at the 40m mark, under a pull of 12.5kg. The slope of the measured line is 2-degree 40minutes. The tape weighs 1kg, standard pull of 8.5kg, cross-sectional area of 0.039cm^2 and E= 2x10^6 kg/cm^2. a. Determine the correction for sag of the tape in meter.b. Determine the horizontal distance between the theodolite and rod in meters. (Apply 5-decimal places - for letter B only)c. What additional pull must be applied to eliminate the effect of sag?
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at B in kN. b. Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm.
Consider the rod shown. Suppose that hℎ = 170 mm, r = 290 mm. Determine the location (x,y) of the centroid of the rod.
W1 = 10 kN/m P2 = 60 kN a = 2 c = 5 M1 = 35 kNm
A line was recorded as 1750.00 meters long. The standard tape weighs0.65 kg , 30.00m long at 20°C under a 50N pull. During the actualobservation the temperature was 5°C and the tape was suspended undera 75N pull. It was also found that the tape is 3.00mm too long. If the linewas inclined at 3%. E = 200GPa, A = 2.50mm² and the coefficient of linearexpansion is 0.0000116 m/°C.(a) What is the actual inclined distance?(b) What is the actual horizontal distance.
The copper pipe shown in the figure has an outside diameter of 3.375 in. and a wall thickness of 0.386 in. The pipe is subjected to a uniformly distributed torque oft= 71 Ib-ft/ft along its entire length. Using a = 2.00 ft, b = 4.50 ft, and c= 9.25 ft, calculate