No cursive Question 1For a bolted assembly with eight bolts, the stiffness of each boltis K,=1.0 MN/mm and the stiffness of the members is km=2.6MN/mm per bolt. The joint is subject to occasional disassemblyfor maintenance and should be preloaded accordingly. Assumethe external load is equally distributed to all the bolts. It hasbeen determined to use M6 × 1 class 5.8 bolts with rolledthreads.(a) Determine the maximum external load Pmax that can beapplied to the entire joint without exceeding the proofstrength of the bolts.(b) Determine the maximum external load Pmax that can beapplied to the entire joint without causing the members tocome out of compression.

Answered: Image /qna-images/answer/62ac1ce6-f3bd-4f01-b5d5-8d03746258bc.jpg

For a bolted assembly with eight bolts, the stiffness of each bolt is K,=1.0 MN/mm and the stiffness of the members is km=2.6 MN/mm per bolt. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly. Assume the external load is equally distributed to all the bolts. It has been determined to use M6 x 1 class 5.8 bolts with rolled threads. (a) Determine the maximum external load P, that can be applied to the entire joint without exceeding the proof strength of the bolts. (b) Determine the maximum external load Pmax that can be applied to the entire joint without causing the members to come out of compression.

For a bolted assembly with eight bolts, the stiffness of each bolt is K,=1.0 MN/mm and the stiffness of the members is km=2.6 MN/mm per bolt. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly. Assume the external load is equally distributed to all the bolts. It has been determined to use M6 x 1 class 5.8 bolts with rolled threads. (a) Determine the maximum external load P, that can be applied to the entire joint without exceeding the proof strength of the bolts. (b) Determine the maximum external load Pmax that can be applied to the entire joint without causing the members to come out of compression.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The horsepower required to drive 40 mm power screw having a pitch of 8 mm, is 3 hp. The screw is single threaded and is made of cold-rolled steel with Sut=550 MPa and Sy=380 MPa and the nut is made of ASTM NO.20 cast iron. The nut height is 50 mm. A factor of safety for possible failures in the threads is 3. If the screw is rotating at a speed of 50 rpm, determine; a) the maximum force that can be applied by the nut b) the efficiency of screw-nut c) the coefficient of friction between the nut and the screw.
Determine the safe tensile load for fine series bolts of (a) M 24and (b) M 38. Assume that the bolts are not initially stressed and take the safe tensile stress as 450MPa.
Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a concentric unfactored live load of 50 kips (dead load = 0) is required to be resisted by the connection and the bolt shear strength controls the design, the minimum required number of bolts is?
An M30 × 3.5 ISO grade 8.8 bolt is used in a joint at a preload levelrecommended for reused connections, and the joint is subject to a repeated tensilefatigue load of P = 65 kN per bolt. The joint constant is C = 0.25.a) Determine the static load factors; b) The factor of safety guarding against a fatigue failure based on the Goodmanfatigue criterion
(7) The cylinder head of a 10”x18” refrigerant compressor is attached by 10 stud bolts made of SAE grade 5. The maximum cylinder pressure is 350psi. (a) What size of bolt is to be used? (b) What approximate tightening torque should be applied to induce a tightening stress of 0.9 time of the proof stress?
Bolt properties: M14 x2 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members. (d) Evaluate Yielding, Load and Joint Separation factor of safeties if the joint is permanently bolted.
Determine the safe tensile load for bolts of (a) M 17 and (b) M 26. Assume that the bolts are not initially stressed and take the safe tensile stress as 305 MPa
Q1. Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting 28 kW at 450 r.p.m. and having an allowable shear stress of 40 MPa. The working stress in the bolts should not exceed 30 MPa. Assume that the same material is used for shaft and key and that the crushing stress is twice the value of its shear stress. The maximum torque is 25% greater than the full load torque. The shear stress for cast iron is 14 MPa.
Draw the Mohr Circle and mark important points for a rod under pure tensile load & torsion
1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?
The effective handle length of a wrench is 30 cm. The bolt is made of grade 5 steel. What is the minimum diameter of the bolt that can be tightened with this tool if a force of 50 N is applied and you want to respect a safety factor of 6 on the bolt? Answer: 9.04mm
(12) A turnbuckle connects two rods having ⅜-16 UNC threads. The thread friction is 0.2. How much external torque is necessary to stress the rods 500lb if it is assumed that neither rod turns as the turnbuckle is tightened? The mean diameter of the threads is 0.335 in.