The 10-kg wheel is rolling under the constant moment of M = 97 N-m. The wheel has radius r= 0.59 m, has mass center at point G, andthe radius of gyration is kg = 0.27 m. The coefficients of friction between the wheel and the ground is ls = 0.25 and Hk = 0.14. If thewheel rolls while slipping, determine the magnitude of the linear acceleration of point G (in m/s2). Please pay attention: the numbersmay change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?.MG

Answered: Image /qna-images/answer/9091581d-969b-42e3-b717-f023c019c532.jpg

The 10-kg wheel is rolling under the constant moment of M = 97 N-m. The wheel has radius r= 0.59 m, has mass center at point G, and the radius of gyration is kg = 0.27 m. The coefficients of friction between the wheel and the ground is ls = 0.25 and Uk = 0.14. If the wheel rolls while slipping, determine the magnitude of the linear acceleration of point G (in m/s2). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M

The 10-kg wheel is rolling under the constant moment of M = 97 N-m. The wheel has radius r= 0.59 m, has mass center at point G, and the radius of gyration is kg = 0.27 m. The coefficients of friction between the wheel and the ground is ls = 0.25 and Uk = 0.14. If the wheel rolls while slipping, determine the magnitude of the linear acceleration of point G (in m/s2). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
The solid homogeneous cylinder shown has a mass of 30 kg and is rotating at 1200 rpm clockwise about a fixed horizontal axis through O. The coefficient of kinetic friction between the brake and the cylinder is 0.20. If the tension in the spring when the brake is applied is 100 N, determine the time required for the cylinder to stop rotating. Neglect the thickness of the vertical members. (Draw FBD)
6/40 If the frictional moment at the pivot O is 2 N+m, de- termine the angular acceleration of the grooved drum, which has a mass of 8 kg and a radius of gyra- tion kg = 225 mm. 200 mm kg 12kg
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μkμk = 0.2. Neglect the mass of the Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.
The 100-kg thin circular disk rolls without slipping on the horizontal plane. Determine a) The angular acceleration of the disk. b) The friction acts on the disk.
A force was applied to a 50 kg wheel as shown in the figure. If the wheel starts to rest without slipping Determine the angular acceleration ε, the wheel pressure on the ground N and the rotational speed of the wheel n after 10 revolutions, if the rolling friction coefficient f = 0.1. Take the radius of inertia of the wheel equal to 0.3 m.
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μk = 0.2. Neglect the mass of the cord Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.
The pendulum has a mass of 8.8 kg, a centre of gravity at G, and a radius of gyration of 0.31 m about the fixed pin support at O. At what position (in degrees) must the pendulum by released from rest so that its angular acceleration is 18.6 (clockwise) at that instant? Take = 0.25 m. The motion occurs in a vertical plane and friction is negligible. Choose the correct answer. 43.2 36.7 34.6 48.4 41.1
The right‐angle plate is formed from a flat plate having a mass ρ per unit area and is welded to the horizontal shaft mounted in the bearing at O. If the shaft is free to rotate, determine the initial angular acceleration α of the plate when it is released from rest with the upper surface in the horizontal plane. Also determine the y‐ and z‐components of the resultant force on the shaft at O.
The desk has a weight of 54 lblb and a center of gravity at GG. The coefficients of static and kinetic friction at AA and BB are μsμs = 0.5 and μkμk = 0.2, respectively. (Figure 1) Determine the initial acceleration of a desk when the man applies enough force FF to overcome the static friction at AA and BB. Find the vertical reaction on each of the two legs at AA.
The drum, with radius R = 1.9 m, is given an initial counterclockwise angular velocity ω0. The drum is kept from rolling towards the left by a smooth vertical slot acting on a thin rod which passes through its centre. A vertical force (where C = 38, k = 1.7 and t denotes time in seconds) is being applied to a cord wrapped around the inner hub, with radius r = 0.7 m, of the drum. If the frictional coefficient is μk = 0.62 and the change in the angular momentum about O is ΔHO = 238 kg.m2/s (counterclockwise) during the first 2.3 seconds, determine the mass of the drum. (The mass of the cord and the thin rod may be regarded as negligible.) a)214.2 kg b)68.28 kg c)19.83 kg d)109.6 kg e)69.86 kg
The shown spool has a mass of 450 kg and aradius of gyration Gk=1.2 m. It rests on thesurface of conveyer belt for which the coefficient offriction m= 0.5. If the conveyer acceleratesat2 1.2m / S and the spools rolls without slipping,determine the tension in the wire and the angularacceleration of the spool