For a H bridge converter with given spesifications find the following by hand Vin = 240V (DC) f = 5kHz C = 1uF Rload 100 ohm Duty cycle = 2*pi*50 The load consist of series connection of a resistor and an inductor and an ac voltage source. RI = 20 ohm LI = 20mH El = 20 * cos(2*pi*200) (AC) 1)The voltage across the load (rms and average) 2) The current flowing through the load (rms and average) 3)The voltage across one of the switching device (T1, mms and average) 4) The current flowing through the switching device (T1, mms and average)

For a H bridge converter with given spesifications find the following by hand Vin = 240V (DC) f = 5kHz C = 1uF Rload 100 ohm Duty cycle = 2pi50 The load consist of series connection of a resistor and an inductor and an ac voltage source. RI = 20 ohm LI = 20mH El = 20 * cos(2pi200) (AC) 1)The voltage across the load (rms and average) 2) The current flowing through the load (rms and average) 3)The voltage across one of the switching device (T1, mms and average) 4) The current flowing through the switching device (T1, mms and average)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

In an R-L parallel circuit, ET=240 volts, R=560 R = 560 2, and XL=330. Find reactive power.
Q.1) Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is resistive with R=10 Ohms. The critical value of L and the critical value of C are equal to: a. 0.625mH and 0.392uF b. 0.625mH and 0.196uF c. 0.312mH and 0.196uF d. None of these
Part 1) Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is resistive with R=10 Ohms. The critical value of L and the critical value of C are equal to: a. 0.625mH and 0.392uF b. 0.625mH and 0.196uF c. 0.312mH and 0.196uF d. None of these Part2) Now consider the same given but the load is an inductive load with R=10 Ohms and L=10 mH. The switch is ideal. Calculate The RMS load current Io and the RMS converter current Ir are equal to: Select one: a. 5A and 3.54A b. None of these c. 8A and 5.66A d. 12.5A and 8.84A
For buck DC-DC converter has VS = 50v duty cycles =0.4 with L = 400μH , C = 100MF and R = 20Ω if the switchingfrequency is 20kHz Find 1.VO 2.ILmax 3. ILmin 4. Outputvoltage ripple
5. Build the phase splitter circuit using : a- OP_AMP circuit. b- Center tap transformer
1) For the BOOST converter, a DC 50 Volt DC voltage of B Volt is taken into an A ohm load. If inductance current is continuous and operating frequency is 10 Khzc : 100UF ;(30) a) Draw the circuit diagram b) Find the work rate c)Find the minimum required inductance value d) Find the Imin and Imax valuee) Find the power consumed by the load
A three phase converter has a rating of 600 kW when operating at unity power factor. Neglecting any change in efficiency, what would be its rating when operating at a power factor of 0.85. (ILLUSTRATIONS such as diagrams and graphs are Required).
(A) Design a DC Power Supply Circuit with fix output (+5V & 3.3V) and variable output from (0 to 15V - 2A). Assume that the secondary output voltage of the transformer is 12Vrms for the standard 230v 50Hz.
Design a buck converter such that the output voltage varies between from 20V to 28V while the input voltage is 40V. The maximum load power is 200Wde. Assume the switching frequency is 15kHz. (a) Design the converter such that it will be in continuous current mode. (b) The capacitor realized output voltage ripple must not be more than 1% at worst case. (c) The inductance realizes CCM at worst case. (d) Select the appropriate switch and other elements
Find full load current..
In the figure below, since Vcc=12V, Vbb= 5V, ß=100, Rc= 3 kΩ , Rb= 200 kΩ , how many Ib=? milliamperes (take Vbe=0.6 V)
Please solve this problem in detail A step up DC converter is used to control power flow from a DC votage Vs = 100V to a battery voltage E = 200V. The power transferred to the battery is 20 kw. The current ripple of the inductor is negligible. The duty cycle and the effective load resistance as seen from the input are respectively equal to: Select one: a. None of these b. 0.5, 0.5 Ohms c. 0.33, 0.5 Ohms d. 0.5, 0.33 Ohms