The beam is supported by a pin at A and a short link BC. Determine the maximum magnitude P of the loads the beam will support if the average shear stress in each pin is not to exceed 80 MPa. All pins are in double shear as shown, and each has a diameter of 18 mm. 4P 4P 2P 0.5,m 0,5m 1 m -1.5 m 1.5 m 30 B

The beam is supported by a pin at A and a short link BC. Determine the maximum magnitude P of the loads the beam will support if the average shear stress in each pin is not to exceed 80 MPa. All pins are in double shear as shown, and each has a diameter of 18 mm. 4P 4P 2P 0.5,m 0,5m 1 m -1.5 m 1.5 m 30 B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the shear stress (in Mpa) in the 23.5-mm-diameter pin at A that support the beam if P = 28.36 kN, a = 2.25 m, and b = 6.56 m.
BADLY NEEDED ANSWER ASAP Determine the shear stress (in Mpa) in the 20.75-mm-diameter pin at A that support the beam if P = 28.96 kN, a = 2.12 m, and b = 5.72 m. Round off the final answer to three decimal places.
The beam shown is supported by a pin at C and by a short link AB. If w = 15 kN/m, determine the average shear stress in the pins at A and C. Each pin has a diameter of 20 mm. Assume L = 1.6 m and θ = 35°.
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
Determine the shear stress (in Mpa) in the 28.36-mm-diameter pin at A that support the beam if P = 29.48 kN, a = 2.86 m, and b = 5.57 m. Round off the final answer to three decimal places.
Consider the wooden member subjected to a tensile load P = 11.00 kN. Determine the shear stress at the inclined section as shown.
All pins are in double shear, each has a diameter of 13mm, and the average shear stress in each pin is not to exceed 65 MPa. Determine the maximum magnitude P of the loads that the beam can support
The two members used in the construction of an aircraft fuselage are joined together using a 30° fish-mouth weld. Determine the average normal and average shear stress on the plane of each weld. Assume each inclined plane supports a horizontal force of 400 lb.
The beam is constructed from two boards fastened together at the top and bottom with three rows of nails spaced every 8 in. If an internal shear force of V = 800 lb is applied to the boards, determine the shear force resisted by each nail.
A motor delivers 500 hp to the shaft, which is tubular and has an outer diameter of 2 in. If it is rotating at 200 rad>s, determine its largest inner diameter to the nearest 1 8 in. if the allowable shear stress for the material is tallow = 25 ksi.
The shaft is supported by a thrust bearing at A and a journal bearing at B. If P = 20 kN, determine the absolute maximum shear stress in the shaft.
Determine the maximum shear force V that the strut can support if the allowable shear stress for the material is tallow = 40 MPa.