For every four seconds,8.77E10^19 e- move past agiven point in a circuit. Howmuch current would it take tomove 9.63E10^19 e- past apoint given the same amountof time? *Your answerWhat is the resistance of acopper specimen with aninitial resistance of 250 ohmsat 38 degrees Celsius? Presenttemperature is 48 degreesCelsius and RTC at O degreeCelsius of 1/237.6 per degreeCelsius? *Your answer

As per the guidelines of bartleyby I need to answer first question only.

Answered: For every four seconds, 8.77E10^19 e-…

For every four seconds, 8.77E10^19 e- move past a given point in a circuit. How much current would it take to move 9.63E1O^19 e- past a point given the same amount of time? *

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Steps to find the reflection coefficient of the electrically transverse wave in terms of (O . 0) ?

Q: 5s^2+ 29s+ 30)/(s^2+ Ex. 516. F(s)= ( f(t)= A*delta(t) + G exp( -H t ) sin( omega t + K ). Determine...

A: The solution is given below

Q: If a 120ohm resistor is wired in parallel with a 30ohm resistor and a 9v battery. a. Draw the circu...

A: Resistor A resistor is a passive element. Resistors are used to reduce current flow,

Q: 12–29. A ball A is thrown vertically upward from the top of a 30-m-high building with an initial vel...

A: Given: A ball A is thrown vertically upward from the top of a 30-m-high building with an initial vel...

Q: Explain this statement- “While the Shannon capacity gives us the upper limit; the Nyquist formula te...

A: To understand this statement we will refer to terms " Shannon capacity" and " Nyquist bit rate".

Q: B1(b) A Single-phase, 50 Hz, overhead line delivers 1500 kW at 11 kV, 0.8 p.f. lagging. The total li...

Q: PR1 + REF1 V 2 R1 V1 1k2 | 2V 1kHz 0° С1 REF1 1000F 1. (+

Q: RT, IT, 11, I 2, 1 3, I 4, I 5, 16 I3 R1= 3kN R3= 2k2 I Rs= 5kN I6 111V R2= 8kN R= 7k2 R= 6k2

Q: Derive the formula for Average Power, Pavg = VI cosθ watts, where V is the root-mean-square (rms) vo...

A: To derive the formula for Average power Pavg = VI cosθ watts

Q: Given the following wye-connected resistances: Ra = 11 Ω, Rb = 4 Ω, and Rc = 11 Ω, calculate the val...

Q: Find: RT, V1, V2, V3 (vdr) I= 3A R1= 32 R2= 102 R3= 52

A: In this question we need to find equivalent resistance , voltage across R1 , R2 & R3 .

Q: For the emitter-stabilized bias configuration, determine: IE VCE re Zi Zo

Q: Energy is the capacity to do work, measured in joules (J). * No Yes In this figure below we have: 5Ω...

A: Yes Energy is the capacity to do work Having Energy in a system means that it is capable of doing wo...

Q: R3 R2 R1 R5 R4 Rg R6 R7 b

Q: 80260°V 3+j6N 2-j50 j30 d. a e 10020°V 5040°V 2-j100 3+j70 i h g f

Q: Are the state space equations for the r = Ar + Bu correct? 1 -k k +. 文。 M M M, 13 -b, * 0. 文。 -k M M...

A: We need to tell about whether the given statement is true or false.

Q: Which of the following is a viable clean and renewable alternative to the use of nuclear power to ge...

A: Answer: Natural Gas Explanation: A. It is a valid option. Natural gas is a clean renewable alternati...

Q: Q2) for LTI discrete time system described by: y(n) = 2 y(n-1) + x(n) y(-1) = 0.1 x(n) = (0.4)" u(n)...

Q: 2. Kirchhoff's Current Law (KCL) Experimental Procedure Design the circuit using resistors and power...

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts fo...

Q: (а) Figure Q1(a) shows an amplifier with negative feedback. Explain how does the inclusion of the ne...

Q: Ex. 506. Determine the Inverse Laplace Transform of the signal: F(s)=90* (s+12)*(s+16) / ( (s+9)*(s+...

A: The solution is given below

Q: I'm trying to study Microcontroller instructions (PIC16F877A) by Assembly (35 instructions), so I ne...

A: Microcontroller- Microcontroller is a form of integrated chip. It a combination of memory, input out...

Q: An amplifier without feedback has an internal gain of -500 with a distortion of 10% and a normal inp...

Q: An EMF of 200Vat a frequency of 2kHz is applied to a coil of pure inductance 50mH. Determine a) the ...

Q: Question # 2: A 2000/400 V, 100 kVA, 60 Hz step-down single-phase transformer has a primary and seco...

Q: periodic convolution using DFT and IDFT method.

A: Delta Function-It is also known as the unit impulse function. It's value is equal to zero everywhere...

Q: 4+j30 3+j60 j3n N) 10020°V 3-j6N 50 5+j80

Q: Determine the current l2 in the circuit below in polar form. Write the magnitude only in four decima...

Q: Given the sequential circuit below, derive the excitation table. RQ FF1 Y X- Emphasis RQ %24 FF2 Wha...

A: For FF1 the output be 'A' For FF2 the output be 'B' In the given problem, C is given there is no In...

Q: An amplifier without feedback has an internal gain of -500 with a distortion of 10% and a normal inp...

A: Given- A(gain without feedback) = -500 D (Distortion without feedback) = 10 Vin (input voltage) = 0....

Q: * 15. For the cascaded system of Fig. 10.55 with two identical stages, determine: (a) The loaded vol...

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are...

Q: DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICS TOPIC: TRANSFORMERS NOTE: P...

A: Current transformer: This is used to measure a very high current value. This gives current on the se...

Q: The polarity test is performed upon a transformer. If the input voltage is Vin and the voltmeter rea...

A: In this question, We need to Calculate the turns ration. If the polarity test is performed upon a t...

Q: A positive-sequence, balanced delta-connected source supplies a balanced delta- connected load. If t...

Q: 1202 – 20° V. If the One line voltage of a balanced Y-connected source is Vab source is connected to...

Q: For the emitter-stabilized bias configuration, determine: IE VCE re

A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost other par...

Q: In this section, you will describe the major responsibilities that must be fulfilled during the inst...

A: With the advancement of microprocessor, microcontroller, Intergrated IC, Design of Electronics circ...

Q: 2. Find the current in the 5 ohms resistor in the circuit. (Hint: combination of nodal and Thevenin'...

A: Here To find the current through 5 ohm Nodal analysis can be done and The values of node voltages ...

Q: Which Boolean algebra property allows us to group operands in expression in any order without affect...

Q: al Calculate the currents of the branches and determine v1, v2. b/ Find the power of sources,

Q: Figure below shows a negative feedback system. The open loop gains of amplifiers are given as follow...

A: Given: The figure below shows a negative feedback system. The open-loop gains of amplifiers are give...

Q: i) Consider the system shown below. Determine the value of k such that the damping ratio is 0.5. The...

A: Answer -

Q: Given a sphere that has Q=30 micro C, radius a=10 mm Find electric field intensity E that is 5 mm aw...

Q: The cost of insulation for underground cable is less than the cost of insulation for TRUE / FAL over...

Q: Quantity Relationship (for Intrinsic Si at T-300 K) B- 73x 10"cm®Kª E,- 1.12 ev k- 8.62 x 10 eV/K ,-...

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are...

Q: Find the equivalent inductance of the circuit if L= 20H 25 H 20 H 20 H 60 H. 10 H 30H

A: In this question we will find equivalent inductance of circuit....

Q: DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICS TOPIC: TRANSFORMERS NOTE: P...

A: A Three-phase system is used to generate and transmit large amount of power. Three-phase transformer...

Q: 1. Given the operational amplifier below. a. Solve for the input voltage, if the feedback resistors ...

Q: Warmup: 1. Find the current in the circuit. 20 ohm 40 ohm 120V I 2. What is the voltage across the 4...

A: In this question, We need to determine the current I in the given series circuit. We know if two r...

Q: (a) DN; (b) Da (c) \D1l;

A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost other par...

Question

100%

For every four seconds,
8.77E10^19 e- move past a
given point in a circuit. How
much current would it take to
move 9.63E10^19 e- past a
point given the same amount
of time? *
Your answer
What is the resistance of a
copper specimen with an
initial resistance of 250 ohms
at 38 degrees Celsius? Present
temperature is 48 degrees
Celsius and RTC at O degree
Celsius of 1/237.6 per degree
Celsius? *
Your answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate for: rise time, delay time, peak time, settling time, and percent peak overshoot
In the circuit given belowX=7andY=5Ωas they are defined as;Vvoltage phasoramplitudehow many volts?NOTE: Please enter your answers as 2 digits after the comma.
Q8 - You wish to end up with a 2um width metal line (measured at the top of the metal lead cross section). A) You are using an isotropic wet etch process on a 1um thick metal layer. What linewidth should the protective photoresist line be to get these results? Sketch the resulting structure before photoresist strip. B) now you are using a completely anisotropic etch, what is the requisite linewidth of the photoresist to achieve the same end goal? Sketch the resulting structure before the stripping of the photoresist.
How would the power delivered to the LED in the circuit below be affected if the below were adjusted? Make sure to submit your answer in words. a) Frequencyb) Amplitudec) DC Offsetd) Time per Division
introduction about PROTOTYPE OF PIEZOELECTRIC BALLAST FOR GENERATING ELECTRIC POWER THROUGH FOOTPASS TRAFFIC
answer the following question regarding circuits:
Find io(t) if vs(t)=400sin2500tV. Suppose that io(t)=I0cos(ωt+ϕ), where −180∘<ϕ≤180∘. Determine the values of I0, ω, and ϕ. Express your answers using three significant figures separated by commas. Enter I0 in amperes, ω in radians per second, and ϕ in degrees.
Briefly explain why E = 0 inside a conductor? A conductor is an equipotential’ give your opinion on this statement and explain your opinion. answer must be correct
(ii) Determine the range K to keep the system stable using the Routh-Hurwitzcriterion.
This question from microwave systems course. Good luck in your life.
The following problems refer to grounding requirements. Give the source of yourresponses. 1. What is the minimum size copper grounding electrode conductor for a service withthree sets of parallel 350 kcmil conductors (three conductors per phase)?
Electric Powers System for Nonelectrical Professional can you explain the purpose of capactictors, reactrs, and static VAR compensators used in electric power systems