For laminar flow over a hot flat plate, the local heat transfer coefficient decreases with distance because (select all that are correct) The thickness of the heated region near the plate is increasing. The velocities near the plate are decreasing. The fluid temperatures near the plate are increasing.

For laminar flow over a hot flat plate, the local heat transfer coefficient decreases with distance because (select all that are correct) The thickness of the heated region near the plate is increasing. The velocities near the plate are decreasing. The fluid temperatures near the plate are increasing.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.57P

See similar textbooks

Similar questions

Calculate the rate at which the average friction coefficient, friction force and heat transfer rate will change if the free flow rate of the turbulent air flowing parallel to the plate over a smooth plate is doubled. Does the result change for constant temperature and constant heat flux conditions; Please evaluate.
Consider a bullet piercing through calm air during a short time interval in which the bullet’s speed is nearly constant. Determine if the time-averaged airflow over the bullet during its flight is one-, two-, or three-dimensional
Air at 60°F flows over a 10-ft-long flat plate at 7 ft/s. Determine the local friction and heat transfer coefficients at intervals of 1 ft, and plot the results against the distance from the leading edge.
1. Experimental analysis was carried out about turbulent convective heat transfer in trapezoidal cross-sectioned duct.Average Nusselt numbers and Reynolds numbers were determined for each experiment and the following data set have beenobtained from this investigation. Find an engineering correlation between the average Nusselt number and Reynolds numberin the form ofNu = aReb
Air at 1 atm with a velocity of 4 m/s and a temperature of 50oC flows over a flat plate that is at a uniform temperature of 100oC. The plate has a length of 0.20 m and a width of 0.1 m. a) What is the average heat transfer coefficient? b) What is the heat transfer rate from plate to the air? c)What is the average friction coefficient and the drag force ? d)What is the heat transfer coefficient at x=0.15 m ?
A coated sheet is being dried with hot air blowing in cross flow on the sheet surface. The surface temperature of the sheet is constant at 90°C, while the air velocity and temperature are 0.3 m/s and 110°C, respectively. The length of the sheet subjected to the blowing hot air is 1 m long. Determine the convection heat transfer coefficient and the heat flux added to the sheet surface. Treat the coated sheet as a vertical plate in cross flow.
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C . The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 °C , what is the overall heat transfer at the laminar section?
What is the ratio of total convective heat transfer rate to laminar convective heat transfer rate for the flow over 2 m length flat plate if 10 m/s air velocity is observed? For air: ν = 20x10-6 m2/s
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
Air stream at 1 atm flows with a velocity of 2 m/s, in parallel over a 3 m long square flat plate, placed on ground, where there is an unheated starting length of 1 m. The air stream has a temperature of 20 °C and the heated section of the flat plate is maintained at a constant temperature of 80 °C. Determine the local heat transfer coefficient at trailing edge and average convection heat transfer coefficient for the heated section. Also calculate the heat loss by convection. Determine the average friction coefficient and wall shear stress and drag force.