Question 4 Members of the truss shown in Figure 4 consists of sections of Aluminium pipe with cross-sectional areas as shown. Use E= 70 GPa to determine the vertical deflection of point E caused by the 40 kN load. P=40kN C 梨 Cross-Sectional Areas AAC ACE AAB AAD=500mm² ABD ACD ADE 1000mm² 0.6m D Fig. 4 1.5m 0.8m

Question 4 Members of the truss shown in Figure 4 consists of sections of Aluminium pipe with cross-sectional areas as shown. Use E= 70 GPa to determine the vertical deflection of point E caused by the 40 kN load. P=40kN C 梨 Cross-Sectional Areas AAC ACE AAB AAD=500mm² ABD ACD ADE 1000mm² 0.6m D Fig. 4 1.5m 0.8m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.29P

See similar textbooks

Similar questions

A W8 × 28 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length of the column if (a) P = 50 kips, and (b) P = 100 kips? (Assume E = 29,000 ksi and y = 36 ksi.)
A wide-f hinge member (W 10 × 30) is compressed by axial loads that have a resultant P = 20 kips acting at the point shown in the figure. The material is steel with modulus of elasticity E = 29,000 ksi. Assuming pinned-end conditions, determine the maximum permissible length Lmaxif the deflection is not to exceed 1/400th of the length.
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
An aluminum bar having a rectangular cross section (2.0 in. × 1.0 in.) and length L = 30 in. is compressed by axial loads that have a resultant P = 2800 lb acting at the midpoint of the long side of the cross section (sec figure). Assuming that the modulus of elasticity E is equal to 10 × 106 psi and that the ends of the bar are pinned, calculate the maximum deflection and the maximum bending moment Mmax.
-11 Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 40 kips (see figure). The column has an outside diameter d = 4.0 in., wall thickness t = 0.226 in., E = 29,000 ksi, and y = 42 ksi.
A brass bar of a length L = 0.4 m is loaded at end B by force P = 10 kN with an eccentricity e = 6mm. The bar has a rectangular cross section with an h/b ratio of 1.5. Find the dimensions of the bar if the deflection at the end is limited to 4 mm. Assume that E = 110 GPa.
‘11.5-2 A steel bar having a square cross section (50 mm × 50 mm)and length L = 2.0 in is compressed by axial loads that have a resultant P = 60 kN acting at the midpoint of one side of the cross section (sec figure). Assuming that the modulus of elasticity £is equal to 210 GPa and that the ends of the bar are pinned, calculate the maximum deflection S and the maximum bending moment Mmax.
Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 6 ft, 9 ft, 12 ft, and 15 ft. The column has an outside diameter d = 6.625 in. and wall thickness t = 0.280 in, (Assume E = 29,000 ksi and y= 36 ksi.)
Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 500 kN (see figure). The column has an outside diameter d = 200 mm, wall thickness; = 10 mm, E = 200 GPa, and y = 250 MPa.
A simply supported slender column is subjected to axial load P = 175 kips applied at distance e = 0,5 in. from joint s A and B (see figure). The column has a circular cross section with an outer diameter of 10 in. and wall thickness of 0.5 in. Calculate the height of the column if the maximum deflection caused by the axial loads is 0,1 in. Assume that E = 29,000 ksi.
.16 Three identical, solid circular rods, each of radius r and length L, are placed together to form a compression member (see the cross section shown in the figure). Assuming pinned-end conditions, determine the critical load Pcr The rods act independently as individual columns. The rods are bonded by epoxy throughout their lengths so that they function as a single member. What is the effect on the critical load when the rods act as a single member?
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.