For the amplifier circuit shown in figure below with (a = 0.99) and (r, = 1/h., = 0).determine:V cc + 20V1- re2- (hfe) and (hie)3- dc output voltage (Vc).4- (Zp), (Z;), (Z), and (Z')5- (A,) and (A¡)6- ac output voltage (V.)R. 4 kQRE 9 kQZ,RL10kΩRs$5002R, 1kQ REI 180250mVRE2{ 8202CE

Given : It is the kind notice that according to the guidelines of the company we supposed answer…

Answered: For the amplifier circuit shown in…

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 5R: From a cost standpoint, which system is more economical to install: a master amplifier distribution...

See similar textbooks

Similar questions

Q.4/ Refer to the class AB power amplifier shown below:a. Determine the dc parameters VB(Q1), VB(Q2), ICQ, VCEQ(Q1), VCEQ(Q2).b. For the 5Vrms input, determine the power delivered to the load resistor.c. Determine the approximate input resistance seen by the signal source if ac=100
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
On which criteria the power amplifiers are classified? What is the operating point of a class-A power amplifier? What is meant by efficiency? How much efficiency will be obtained in a class-A power amplifier? What are the applications of power amplifiers?
Suppose that each output channel of a computer’ssound card can be represented by a 1-V ac sourcein series with a 32-Ω resistor. Each channel ofthe amplifier in the external speakers has an inputresistance of 20 k , and must deliver 10 W intoan 8-Ω speaker. (a) What are the voltage gain, currentgain, and power gain required of the amplifier?(b) What would be a reasonable dc power supplyvoltage for this amplifier?
Consider the common-source amplifier shown in Figure P11.50. The NMOS transistor has KP=50 μA/V2, L=5 μm, W=500 μm, Vto=1 V and rd=∞.a. Determine the values of IDQ, VDSQ and gm. b. Compute the voltage gain, input resistance, and output resistance, assuming that the coupling capacitors are short circuits for the ac signal. Repeat Problem P11.50 for an NMOS transistor having KP=50 μA/V2, W=600 μm, L=20 μm, Vto=2 V and rd=∞. Compare the gain with that attained in Problem P11.50.
For the cascaded amplifier of the figure below, calculate the input impedance of the first stage, output impedance of the second stage, total voltage gain, and the output voltage if Vs= 1mV.
Figure Q1(a) shows a Class A power amplifier circuit. Given the output signal is as shown in the figure, where Vm is the peak voltage and T is the period. For all transistors, you may neglect VBE and VCE(sat) in your calculations. (i) Derive an equation for power conversion efficiency, in terms of Vm, VCC, I and RL. Hence, deduce the maximum power conversion efficiency that is achievable. (ii) Determine the worst-case average power dissipation in each transistor under normal condition (i.e. RL is not open or short)
Consider the integrating amplifier circuit in Figure 2. Using nodal analysis, derive an expression for vout for the integrating amplifier. In the circuit in Figure 2, exchange the positions of the 0.1uF capacitor and the 5k resistor. a. Use nodal analysis to generate an expression for vout. b. Using this expression, explain what function this circuit performs on an input signal.
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: 1- Determine the Q point, then illustrate it on the transistor I-V characteristic curves. 2- Is the transistor in the active region? Explain thoroughly. 3- Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. 4- Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. 5- Calculate the current gain, the input resistance, and the output resistance.
What is the output impedance of an Ideal Operation Amplifier? What is the open loop gain of an Ideal Operation Amplifier? What is the gain of a voltage follower operational amplifier circuit? What is the input impedance of this circuit? Draw the circuit. How can I add two voltages values together with on op amp? Using op amps, how to make an AD Converter? A DA Converter? What components determine the frequency of an astable, 555 oscillator? Draw the circuit. Draw a circuit for both an astable and a monostable, 555 multivibrator. What is the duty cycle and percentage duty cycle of a pulse train or square wave? What is the overshoot, rise time, fall time, and pulse width of a pulse and where on the waveform is each measured?
Design a Single-Stage Common Emitter Class A Amplifier Specifications:Voltage Divider Bias Circuit Supply: Any value from 10Vdc to 24VdcLoad: 1kΩVoltage Gain: Any value from 80 to 400Lower Cutoff Frequency: 100 HzSinusoidal source (zero internal resistance): 50mVp-pTransistor: Si, β = 75 • Base-Collector capacitance = 8pF • Base-Emitter Capacitance = 25pF a) compute for the biasing resistances.b) determine the dc transistor terminal voltages and transistor currents.
In the common-emitter amplifier circuit shown in the figure, Vcc=9V, R1=27kΩ, R2=15kΩ, RE=1.2kΩ and RC=2.2kΩ. The transistor has β=100.a-) If Rsig=10kΩ and RL=2kΩ, calculate the IE value of the amplifier.b-) For small signal analysis of the transistor, find the value of Rin by deriving the π-modelc-) Calculate vo/vsig and io/ii.

SEE MORE QUESTIONS

Recommended textbooks for you

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS