For the beam loaded as shown in the fgure 3, determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your %3D answer to 3 decimal places. (10 pts) a = 7.5 m, b = 3.9 m, c = 13.4 kN/m, d = 30 kN. %3D d kN d kN c kN/m BA "b" m "a" m "b" m

For the beam loaded as shown in the fgure 3, determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your %3D answer to 3 decimal places. (10 pts) a = 7.5 m, b = 3.9 m, c = 13.4 kN/m, d = 30 kN. %3D d kN d kN c kN/m BA "b" m "a" m "b" m

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Similar questions

Determine the resultant of the vertical thrusts on the sphere shown in the figure for the data: d=0.6m; R=0.5m;h=4m.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
For the beam loaded as shown in the figure 3, determine the slope at B in degrees using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 5.5 m, b = 3.3 m, c = 20.3 kN/m, d = 27 kN.
Determine the magnitude of the horizontal reaction (N) at A if P = 254 N and Q = 2395 N. Let x = 2.48 m, y = 2.5 m, and z = 2.05 m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the horizontal reaction at A: use R if to the right and L if to the left.
Problem 2. Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solution. Round-off your answers to two decimal places. QUESTIONS: a. Vertical Reaction at B in kN. b. Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. GIVEN: a. 3.1 b. 18.0 c. 20
Step 2 1st condition Bending moment at hinge D =0 Rc*2 = (3*2)*(2/2) Rc = 3 KN Rc = 3 KN (upward) could you explain where these numbers coming? Why that divided by two? and is formula like this: 3kN/m*2m*2m/2m? 2nd condition Bending moment at hinge F =0 RB*2= (3*4)*(3+4/2)-3*7 RB = 19.5 KN RB = 19.5 KN ( upward) Same this formula If you can explain this like drawing this on paper and write where all meters and number come, that would be help me. If you could also tell the direction, where you would calculation them
A block with mass m=(24+12)kg is pulled by a horizontal force P applied at point B in Fig.3. The coefficient of kinetic friction between the surfaces is we = (5A+5)/(25+94). When the acceleration of the block is a=(1+9)/4 m/s?, determine the cable forces Tax and Top- 0=(A+8) A=1
Calculate the value of the deflection at point B due to concentrated load P in the form ??=??????????? Note: EI will cancel out in further calculations. Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
For the beam loaded as shown in the figure 1, determine the reaction at A in kN using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 4.7 m, b = 18 kN/m, c = 15 kN.
An overhanging beam supports the loads as shown in the figure. If El 3000.65 kNm², determine the value of deflection at point Fin millimeters.
Do answer ASAP. The section of a concrete dam is shown. Determine if the dam shown is stable against sliding and overturning. The following data is available:Concrete density: ρconc = 2400 kg / m³ Coef. Soil-Dam Static Friction: μs = 0.30Density of water: ρwater = 1000 kg / m³ Coef. Soil-Dam Kinetic Friction: μk = 0.20
For the beam loaded as shown in the figure 2, determine the reaction at D in kN using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 2.9 m, b = 32.9 kN/m, c = 20 kN.