For the bronze segment AB, the maximum shearing stress is limited to 8000 psi and for the steel segment BC, it is limited to 12 ksi. Determine the diameters of each segment so that each material will be simultaneously stressed to its permissible limit when a torque T = 12 kip-ft is applied. For bronze, G = 6 × 106 psi and for steel, G = 12 × 10° psi. Bronze Steel 4ft 6 ft

For the bronze segment AB, the maximum shearing stress is limited to 8000 psi and for the steel segment BC, it is limited to 12 ksi. Determine the diameters of each segment so that each material will be simultaneously stressed to its permissible limit when a torque T = 12 kip-ft is applied. For bronze, G = 6 × 106 psi and for steel, G = 12 × 10° psi. Bronze Steel 4ft 6 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The design of a machine element calls for a 40-mm-outer diameter shaft to transmit 45 kW. (a) If the speed of rotation is 720 RPM, determine the maximum shearing stress in shaft a. (b) If the speed of rotation can be increased 50 % to 1080 RPM, determine the largest inner diameter of shaft b for w/c the maximum shearing stress will be the same in each shaft.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. The modulus of rigidity is 3.7 × 106 psi for aluminum and 5.6 × 106 psi for brass. Take T = 13 kip·in. a) Determine the maximum shearing stress in cylinder AB. b) Determine the maximum shearing stress in cylinder BC.
Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20-mm diameter wire on a mean radius of 80 mm when the spring is supporting a load of 2 KN.
Determine a.) the maximum torsional stress, τmax, and b.) the maximum angle of twist, φ, of the solid shaft if the shaft has a diameter of d = 50 mm and the shear modulus is G = 75 GPa.
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing stress is 85 MPa. The pipe CD, which has an outer diameter of 90 mm and a wall thickness of 6 mm, is made of an aluminum for which the allowable shearing stress is 54 MPa. Determine the largest torque T that can be applied at A
The driveshaft of an automobile is being designed to transmit 238 hp at 3790 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 5700 psi.
The steel jacket CD has been attached to the 40-mm-diameter steel shaft AE by means of rigid flanges welded to the jacket and to the rod. The outer diameter of the jacket is 80 mm and its wall thickness is 4 mm. If 500 N·m torques are applied as shown, determine the maximum shearing stress in the jacket.
A solid bar having a diameter of 160 mm is to be replaced by a rectangular tube having cross-sectional area of 150 mm x 310 mm to the median line of the cross-section. (a) Determine the required thickness of the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar. (b) Determine the shear stress in the tube . If it is subjected to a torque T = 15 kN-m and a thickness of 10 mm. and (c) Determine the angle of twist in degrees of the tube if the length of the tube is 1000 mm and the shear modulus is 75 GPa. Thickness of the tube is 10 mm and the torque T = 15 kN-m.
The electric motor exerts a torque of 800N*m on the steel shaft ABCD when it rotates at a constant speed. Design specifications require that the shaft diameter is uniform from A to D and that the angle of twist between A and D does not exceed 1.5°. If it is known that the maximum shear must be less than or equal to 60MPa and G=77GPa. Determine the diameter which can be used for the axis. The figure is in the attached image
A 88-N·m torque is applied to a hollow shaft having the cross section shown. Neglecting the effect of stress concentrations, determine the shearing stress at points a and b. The shearing stress at point a is MPa. The shearing stress at point b is MPa.