For the circuit shown, a closed switch is represented by a logic 1, and an open switch by alogic 0. If v = 5 V across the resistor R is represented by a logic 1, and v0, then what Boolean expression of the state of the switches best describes the voltageOV by a logicacross the resistor?భోమడ్ముS3S2+5 VO R= (S1 + S2) (S3 + S4)O R= S1 S2 S3 S4O R= Si S2 + S3 S4O R= S1 + S2 + S3 + S4

For the circuit shown, a closed switch is represented by a logic 1, and an open switch by a logic 0. If v =5 V across the resistor R is represented by a logic 1, and v = 0 V by a logic 0, then what Boolean expression of the state of the switches best describes the voltage across the resistor? S1 S3

For the circuit shown, a closed switch is represented by a logic 1, and an open switch by a logic 0. If v =5 V across the resistor R is represented by a logic 1, and v = 0 V by a logic 0, then what Boolean expression of the state of the switches best describes the voltage across the resistor? S1 S3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Subject: Digital Logic Design Paint Manufacturing plant.A liquid chemical is used in a manufacturing process. The chemical is stored in three different tanks. A level sensor in each tank produces a HIGH voltage when the level of chemical in the tank drops below a specifiedpoint. Design a circuit that monitors the chemical level in each tank and indicates when the level in any two of the tanks drops below the specified point. Write the Boolean SOP expression for the the Circuit.
TOPIC: Design, Implementation, and simulation of Combinational circuits using K- Map. Simplify the following expression using the Karnaugh Map (K-Map) and implement. Write a truth table for the expression (shown in the picture) and then draw a simplified logic diagram. Implement the expression on the Multisim software and insert snapshots of the implementation. The expression is shown in the picture below:
Given the logic expression, fill up the truth table and simplify the equation using k-mapping. show clear full solution and the actual k-mapping. I give my thanks in advance :). Note: i already asked a question for this but i'm asking again just to be sure because the final answer from the previous tutor was 1 and i was supposed to make a final circuit out of that as well, and i'm currently not sure how to do that if T=1.
Design a logic circuit that will tell you if a given month has less than 31 days. The month is specified by a zero-indexed four-bit number M[3:0]. For example, 0000 is January and 1011 is December. The logic circuit output Y is 1 when the month specified at the input by M[3:0] has 31 days. Find the simplified expression using K-Map and draw the logic circuit diagram.
- The proportional distribution of A, B, C, D signals is given in the table as a percentage. It “logic 1” when the signals are accepted as active, “logic 0” when they are accepted as passive. takes. - When the proportional sum of active signals is over 50%, its output is "logic1", When we accept "logic 0" when it is below 50%, the output in the table Find the values. - Create an X function based on the logic values you find. Simplify the created X function. - Design the simplified function with NAND and NOR gates. - Set up the circuits you designed with NAND and NOR gates and observe the outputs. Show the output values by drawing a table, applying all possibilities to the input values.
- The proportional distribution of A, B, C, D signals is given in the table as a percentage. It “logic 1” when the signals are accepted as active, “logic 0” when they are accepted as passive. takes. - When the proportional sum of active signals is over 50%, its output is "logic1", When we accept "logic 0" when it is below 50%, the output in the table Find the values. - Create an X function based on the logic values you find. Simplify the created X function. - Design the simplified function with NAND and NOR gates.
Subject 1: Logic Circuit and Switch Theory Solve (101001-011) * 1001 → Show your solution
Given the following Logic function in standard SoP form F (A, B, C,D) = Σ (m4, m5, m7, m8, m10, m11, m13, m15) Simplify F through Karnaugh map using Maxterms. (Show your calculations)
A device used in cases where only 2 people work in a business where A. and B workers work, gives "logic 1" output if there are only 2 people in the workplace, first obtain the truth table to create the circuit that expresses this situation, then POS Write the function (according to the maxterms) and then draw the circuit of this function. We do not make any simplification in function and circuit. Make sure that your solutions and drawings are legible.
Logic Gate and Its Application [5] F(w,x,y,z) = (2, 3, 6, 8, 11, 12, 14) (a) Show F on a K-map. (b) Obtain a minimal sum of products expression for F. (c) If the minterms: m4, m0, m13 and m15 will never occur determine a new minimal sum of products expression for F.
Design a logic circuits w/ 4inputs (A(MSB), B,C,D(L,S,B)) and 1 output x. The 4 inputs represent switches in a vending machine. The switches can be either open (0) or closed (1) The X output becomes high if and only there are two or more switches closed at the same time. Furthermore it is impossible for the first A and the last switch D to be closed at the same time. Reqd: 1.) complete and labeled truth table 2.) canonical sop form expression 3.) grouped kmap 4.) minimum SOP expression
For the logic circuit shown below complete the following three steps: 1. Write out the Boolean equation of the circuit. 2. Using the rules and laws of Boolean Algebra simplify the equation to it's simplest form. You must show all steps of your simplification to receive credit for your answer. 3. Draw the simplified logic circuit