For the circuit shown below, an impedance having a constant phase angle of -36.87° is connected across the load terminals a and b in the circuit shown below. The magnitude of ZL is varied until the average power delivered is the most possible under the given restriction What settings of R and XL transfer the most average power to the load? 3000 N j4000n a R 10 /0° V (rms) jXc Select one: O a. RL = 5000 and XL = 0 Ob. R= 4000 and XL= 0 O c. R= 0 and XL= -3000 Od. R= 4000 and XL= -3000

For the circuit shown below, an impedance having a constant phase angle of -36.87° is connected across the load terminals a and b in the circuit shown below. The magnitude of ZL is varied until the average power delivered is the most possible under the given restriction What settings of R and XL transfer the most average power to the load? 3000 N j4000n a R 10 /0° V (rms) jXc Select one: O a. RL = 5000 and XL = 0 Ob. R= 4000 and XL= 0 O c. R= 0 and XL= -3000 Od. R= 4000 and XL= -3000

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
A Y-connected balanced three-phase source is feeding a balanced three-phase load. The voltage and current of the source coil are: Calculate the following: The rms phase voltage. The rms line-to-line voltage. The rms current in the source. The rms current in the transmission line. The frequency of the supply. The power factor at the source side, state leading or lagging. The three-phase real power delivered to the load. The three-phase reactive power delivered to the load. If the load is connected in delta configuration, calculate the load impedance.
1-In series R-L circuit transients, the momentary current imm is directly proportional to the RMS voltage. Select one: True False 2-Symmetrical components method are used to solve the symmetrical faults. Select one: True False 3-If the circuit has leading power factor, then it is called as _______________ circuit. Inductive Capacitive Resistive Resistive and Inductive
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the RMS line current at load 1 and 2 respectively?
A 15kV, 3 phase circuits feeds a load of 10,000 kW at a lagging load factor and the load current of 750A. If it is desired to improve the power factor, determine the following: The uncorrected power factor;Reactive load;The new corrected power factor after installing a shunt capacitor unit with a rating of 9000 kVAR. (a) 0.813 lagging (b) 14723 kVAR (c) 0.9 lagging (a) 0.613 lagging (b) 15723 kVAR (c) 0.75 lagging (a) 0.713 lagging (b) 13723 kVAR (c) 0.85 lagging (a) 0.513 lagging (b) 16723 kVAR (c) 0.80 lagging
From the following circuit, which is fed by an alternating voltage source, do as indicated. A. Calculate the equivalent total impedance (describe both complex impedance and phasor impedance). B. Calculate the total rms phasor current of the circuit. NOTE: THE VALUES CORRESPOND TO THE EVEN OR ODD TERMINATION OF YOUR TICKET NUMBER. VALUES FOR TICKET TERMINATION IN EVEN NUMBER: v (t) = 24cos (250t + 45) V R = 1 kΩ L = 300 mH C = 1000 pF VALUES FOR TICKET TERMINATION IN ODD NUMBER: V (t) = 32cos (420t + 35) V R = 2.7 kΩ L = 450 mH C = 100 μF
1. a) Find the rms magnitude and the phase angle of ICA in the circuit shown. 2. b) What percent of the average power delivered by the three-phase source is dissipated in the three-phase load?
A 3-phase Y-connected load draws power from a 3-phase Y-connected source. The source voltage, ?=440∠0º?_rms and the load impedance, Z_y=(30+j15) Ω. The line impedance, Z_line= (1+j1)Ω and the system operates at 60 Hz. a) Draw the single-phase equivalent circuit and label all given quantities numerically. b) Calculatethe rms line (phase) current phasor in each phase. c) Calculate the total active or real power supplied by the source. d) Calculate the total active or real power consumed by the load. e) Calculate the total line loss i.e. the total activepower lost due to line. f) Determine the power efficiency of the system.