For the figure below find 1) Volumetric Flow rate (Q)MH2O 1.677O 6.47818.45312.146MH1CHW = 80Diameter = 18Ground Surfaceelev. = 1968Full PipeDistance between MH1 & MH₂ = 300Ĵelev. = 1962'

Name: For the figure below find 1) Volumetric Flow rate (Q)MH2O 1.677O 6.47
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: For the figure below find 1) Volumetric Flow rate (Q)MH2O 1.677O 6.47818.45312.146MH1CHW = 80Diameter = 18Ground Surfaceelev. = 1968Full PipeDistance between MH1 & MH₂ = 300Ĵelev. = 1962'

Answered: Image /qna-images/answer/87d93b1b-a22a-4042-8f1c-493faf6ec79e.jpg

Engineering

Mechanical Engineering

For the figure below find 1) Volumetric Flow rate (Q) MH2 O 1.677 O 6.478 18.453 12.146 MH1 CHW = 80 Diameter = 184 Ground Surface elev. = 1968 Full Pipe Distance between MH1 & MH₂ = 300' elev. = 1962'

For the figure below find 1) Volumetric Flow rate (Q) MH2 O 1.677 O 6.478 18.453 12.146 MH1 CHW = 80 Diameter = 184 Ground Surface elev. = 1968 Full Pipe Distance between MH1 & MH₂ = 300' elev. = 1962'

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data were obtained for the flow of 20°C water at20 m3/h through a badly corroded 5-cm-diameter pipe thatslopes downward at an angle of 8°: p1 = 420 kPa, z1 = 12 m,p2 = 250 kPa, z2 = 3 m. Estimate (a) the roughness ratio ofthe pipe and (b) the percentage change in a head loss if thepipe were smooth and the flow rate the same.
Find the pressure at point 2 given the isometric drawing of the commercial steel pipeline indicating the straight pipes length and with the following data below:Loss coefficients:• check valve, k = 5.0• gate valves, k = 0.20• elbows, k = 0.75• flowmeter, k = 13.0Pump flowrate = 10 m3/hrFluid power adding by pump = 3.7 HPPressure at point 1 = 60 kPagPipe inside diameter = 50mmViscosity = 0.17 Pa.sSpecific gravity = 0.89Pipe inside surface roughness = 0.00015 ft.
A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
Glycerin, sg = 1.26 and μ = 1.49 Pa-s, flows through a 600-mm Ø pipe at 85 liters per second. a. What is the Reynold’s Number? b. What is friction factor? c. What is the critical velocity?
A Keystone Pipeline has a diameter of 36 inches and a design flow rate of 590,000 barrels per day of crude oil at 40ºC. Estimate the pump horsepower required if the length of the pipe is 2.9 mile(s). The pipe material is new steel. For crude oil at 40ºC, take μ ≈ 0.0053 kg/m-s ÷ 47.88 = 0.0000111 slug/ft-s. The density, with SG = 0.86, is 0.86(1.94) = 1.67 slug/ft3. Take f ≈ 0.0155.
A 60-cm water pipe carries a flow of 0.1 m³/s. At point A the elevation is 50 meters and the pressure is 200 kPa. At point B, 1200 meters downstream from A, the elevation is 40 meters and the pressure is 230 kPa. The head loss , in feet, between A and B isA. 6.94B. 15.0C. 20.88D. 100.2
A Keystone Pipeline has a diameter of 36 inches and a design flow rate of 590,000 barrels per day of crude oil at 40ºC. Estimate the pump horsepower required if the length of the pipe is 2.9 mile(s). The pipe material is new steel. For crude oil at 40ºC, take μ ≈ 0.0053 kg/m-s ÷ 47.88 = 0.0000111 slug/ft-s. The density, with SG = 0.86, is 0.86(1.94) = 1.67 slug/ft3. Take f ≈ 0.0155. Answer is in hp. Last answer was wrong! please help!
After analyzing the flow type in a refinery oil (s = 0.8, v= 1.94x10-4 ft2/s) flowing through a 9inch diameter pipe at (41/1000) ft3/s. Find the following a)centerline velocity b)the velocity at r = 2inch c)the frictional factor d)the shear stress at the pipe wall and e)the head loss per foot of pipe length.
Considering pipe loss only, how much head is required to deliver 0.222 m³/s of heavy fuel oil at 38°C through 914 m of new cast iron pipe, 300 mm inside diameter? Use ε=0.00024 m. (ANSWER MUST BE = 41 m)
Final Ans: Discharge: 0.330 cfs Diameter of Jet: 1.587 in. Mean Velocity: 24.0 ft/sec Lost head: 0.56 ft
7.) The pressure drop associated with hydraulic fluid with a Sg of 0.93 flowing across a 1-in. I.D. sharp edge orifice is 20 lbf/in2 . If the discharge coefficient is 0.60, what flow rate in gal/min could be expected through the orifice?