For the given circuit, the switched is closed for a long time and the switched is opened at t=0. R = 5 k0, C = 47 µF and 11=4 mA given. Calculate the capacitor voltage at t= 0.6 seconds Vc(t=0.6) = ? (Your result must be in Volts) Only give numeric results. (If you found 0.18 Volts, write down 0.18)

For the given circuit, the switched is closed for a long time and the switched is opened at t=0. R = 5 k0, C = 47 µF and 11=4 mA given. Calculate the capacitor voltage at t= 0.6 seconds Vc(t=0.6) = ? (Your result must be in Volts) Only give numeric results. (If you found 0.18 Volts, write down 0.18)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PA: You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor...

See similar textbooks

Similar questions

The switch in the circuit below has been in position a for a long time. At time t = 0 the switch is thrown to position b. You are given the data: Vb = 24 V, C = 10 μF. Vc is the voltage across the capacitor. If the charge on the capacitor at time t =0.3 msec after the switch is thrown is 53.6 μC, what is the value of the resistor R? a) 40 Ω b) 0 Ω c) 20 Ω d) Not enough information.
1. Theoretically calculate the voltage across the capacitor in the circuit of Figure 1 when t = 0 s, 5 s, 10 s, 20 s, 30 s, 40 s, and 60 s, assuming that the circuit is under DC conditions when t < 0 s and the switch is opened at t = 0 s. 2. Compare the calculated voltage at t = 20 s with the experimentally measured ∆?.
A circuit with a supply voltage of 2.5 V is being powered through a package. The packagehas a resistance of 100 m and a certain inductance L. The circuit requires at least 2.25 Vto function correctly. If this voltage is required in a time of 1ns, calculate the effectiveinductance L for the package.
8.3 For a Si solar cell, the dark saturation current is 2 μA and the short circuit cur- rent is 150 mA. When it is optically illuminated, the optically generated current is 0.1 mA. Find the corresponding voltage at current of 100 mA. please tell me his problem in detail
All capacitors were initially discharged. at t = 0, S1 is placed at position 1 and S2 is closed. At t = 15 ms, S1 is placed at position 2 and S2 is kept closed. During this phase, it has been determined that the total resistance seen by the equivalent capacitor is 28 kΩ; and that vT = 10 V at t = 15 ms. Calculate the value of the current iT immediately after the switching occurred. Enter your answer in mA rounded to 2 decimal places. At t = 25 ms, S1 is kept at position 2 and S2 is opened. Data: R1 = 6.5 kΩ, R2 = 10 kΩ, R3 = 1.0 kΩ, R4 = 4 kΩ, R5 = 20 kΩ, R6 = 11.5 kΩ; C1 = 4.5 µF, C2 = 4.0 µF, C3 = 12 µF
Can you find the total energy developed in the circuit? Explain.
7. 7.27 In the circuit the voltage and current expressions are v=48e−25t V, t≥0;i=12e−25t mA, t≥0+.Find1. a) R.2. b) C.3. c) τ (in milliseconds).4. d) the initial energy stored in the capacitor.5. e) the amount of energy that has been dissipated by the resistor 60ms after the voltage begins to decay.
The circuit shown in the attached image contains a voltage source with emf ε = 2.99 V, a resistor with resistance R = 135 kΩ, and a capacitor with capacitance C = 612 nF. When switch S is set to position a, the three circuit elements are in series. When the switch is in position b, the battery is excluded from the circuit. The switch is initially moved to position a, where it remains for a sufficiently long time that the capacitor is fully charged. The switch is now moved to position b. What is the magnitude of the instantaneous current, in amperes, through the resistor the instant the switch makes contact with terminal b? With time meausred the instant that switch S is closed in position b, calculate the time, in seconds, when the charge on the capacitor is one-half of its maximum value. Calculate the current through the resistor, in amperes, at time t = 155.5 ms after the switch is closed in position b.
A 150-volt electromotive force is applied to an RC-series circuit in which the resistance is 1500 ohm and the capacitance is 5 micro Farad (uF). If q(0)=0, find the charge and current at t=0.005 s. charge: q = micro Farad (uF) current: i = milli ampere (mA) Determine the charge as t approaches infinity. charge: q= micro Farad (uF)
Calculate the ratio vC/vT. Enter your answer rounded to 2 decimal places. All capacitors were initially discharged.at t = 0, S1 is placed at position 1 and S2 is closed.At t = 15 ms, S1 is placed at position 2 and S2 is kept closed.At t = 25 ms, S1 is kept at position 2 and S2 is opened.Data: V1 = 17 V;R1 = 3.5 kΩ, R2 = 6 kΩ, R3 = 1.5 kΩ, R4 = 2 kΩ, R5 = 19 kΩ, R6 = 10.5 kΩ;C1 = 4.0 µF, C2 = 4.0 µF, C3 = 12 µF
Derive an expression for the electrical energy stored in a capacitor of capacitance C when charged to a potential difference V. If C = 2µF and V= 4V, calculate(l.) the final energy stored in the capacitor,(II.) the work done by the battery in the charging process Account for any difference between your answers in parts (I) and (II) above
A rectangular cathode with the dimensions width = 2.6 mm and length = 30 mm glows at a temperature of 1800K in a vacuum tube. The work function of the cathode is = 2.5 eV and the emission constant is 3E4 . What is the maximum (saturation) current that can be extracted from this cathode? Hint: If you use the Boltzmann constant in eV enter at least 5 significant digits (i.e. use 8.6174E-5 ) State the current in Amp units.