Show complete solutionFluid Mechanics For the given figure, determine the gagepressure at the bottom of the tank D inPascal unit. Write your answer to thenearest one decimal place. No need towrite the unit and don't write comma toyour answer. * airN15airYaA oil surface0.5 mC watersurface0.5 mOil (s = 0.86) oil surface y0.5 mB oil surfacewaterNYw = 9810Oil(s= 0.86) 1.0 m

Given data in question Unit weight Specific gravity Depths To find out Guage pressure at point D…

Answered: For the given figure, determine the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular tank of diameter 3 m contains water up to a height of 4 m. The tank is provided with an orifice of diameter of 0.4 m at the bottom. Find the time for completely emptying the take Take Cd= 0.60 a.24.8 seconds b.47.8 seconds c.43.8 seconds d.84.7 seconds PLEASE INCLUDE FIGURE OR FBD
A = 1.94.hmax = 0.559.R = 206 1. Filling the tank (30%)a) If the tap on the output pipe is closed (i.e. R = ∞) determine how long it will take the tank to fillup assuming qi = 0.001 m3/s.b) If the tap on the output is open liquid will be coming out at the same time as liquid is going in. Ifthe flow rate in is bigger than flow rate out the height of the liquid in the tank will rise. Using theR value given on the Results Sheet, determine the steady state height of liquid in the tankassuming qi = 0.001 m3/s.c) In theory it will take an infinite amount of time to achieve steady state so in practice we define thetime to respond as the 95% settling time (i.e. the time taken to get to within 5% of the steady stateoutput.) Measure the 95% settling time from your simulation in Q1b). 2. Emptying the tank (10%)a) Assuming the tank is initially full (i.e. h(0) = hmax) and the input is turned off (i.e. qi = 0) the tank willstart to empty. Assuming the R value in Q1b), determine the time…
1)Coefficient of elasticity of a fluid E = 200000 t / m²Considering that for 1 Atmosphere (10 t / m²) pressure increase, the ratio of the decrease in the volume of this fluid to the initial volume iswhich one is given correctly?a) 0.00003b) 0.000004c) 0.00005d) 0.00006e) 0.00007 Please write clearly and clearly. thanks in advance
GIVEN: diameter of sewer pipe = 1.8mDepth of water = 1.6mQ = 2.5m3/sCompute the velocity. Use 3 decimal places all throughout the solution. Box/underline your finalanswer.
PLEASE SHOW COMPLETE SOLUTION WITHIN 30 MINUTES Given: F = 800 N θ = 25° μs = 0.35 Find: Pmin = ? (round of to 2 decimal placed) Pmax = ? (round of to 2 decimal placed)
The end of a cylindrical drummeasures 30 inches in diameter. If thedrum, which measures 3 feet high, iscompletely filled with water, what's thetotal weight of the water in the drum?(Assume water weighs 8 pounds pergallon.)O A. 881 poundsO B. 730 poundsO C. 1235 poundsO D. 3525 pounds
Solve the following problems with accompanying complete solution. boxyour final answer.
Take your tinme on answering given: a.3.7 (m) b.10 (kN/m) c.17.5 (kN) Answer all complete solution
A trapezoidal oil tank has the following dimensions: B1 = 8 3/4", B2 = 15 1/2", the height is 65/8" and it is 10 7/8" long. How many gallons of oil will it hold? (231 cu. in. = 1 gallon)
A liquid is flow throw Rotameter to a tank of size ( L x W x H ) and it is required to full the tank to level of H as shown in Figure . What time is required to full the tank by this liquid ? What time is required to drop the liquid in the tank to from level H to D by rectangular notch ?
Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 kN, just write 120 kN Do not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units specified after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 lb-in, 100 kN)
Two pipes, A and B, contain a fluid flowing under pressure and are connected by a differential gage as shown in the accompanying sketch. The substance in the lower part of the gage has a specific gravity of 1.6 and the surfaces of separation are 18 in. apart. The specific gravity of the fluid is 0.3. If the pipe centers are 4 ft. apart vertically and the pressure in A is known to be 10 psi, what is the pressure in B in psi? Round your answers in 3 decimal places.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

For the given figure, determine the gage pressure at the bottom of the tank D in Pascal unit. Write your answer to the nearest one decimal place. No need to write the unit and don't write comma to your answer. *